{"product_id":"challenger-aa8040001-cylinder-mdl-44060-8-bore","title":"Challenger AA8040001 Cylinder Model 44060 8\" Bore","description":"\u003cp\u003eThe \u003cstrong\u003eChallenger AA8040001 hydraulic cylinder\u003c\/strong\u003e is the direct replacement for the Challenger lift it came off of. This is the genuine Challenger part — same fit and same working specification as the one already on your lift. Ordering the Challenger hydraulic cylinder from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.\u003c\/p\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e AA8040001\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Challenger\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Genuine OEM hydraulic cylinder\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e 44050, 44060\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eNo hydraulic part works alone. A cylinder is only as good as the fluid feeding it, the fluid is only as clean as the reservoir and filter keep it, and a fresh seal kit won't hold in a barrel that's already scored. That's why a leak is worth diagnosing as a system: replace the weeping part, but check the fluid, the fittings, and the bore before you call it fixed.\u003c\/p\u003e\n\u003cp\u003eHydraulic parts almost always fail by leaking. A rod seal starts weeping and the cylinder body goes wet; a hose cracks near its crimp; a fitting's o-ring flattens; the lowering valve stops seating and the lift drifts down overnight. Fluid finds the weakest seal in the loop and pushes past it. The symptom — a puddle, a slow sag, a spongy lift — tells you roughly where in the loop to look.\u003c\/p\u003e\n\n\u003ch3\u003eWhat lifts this hydraulic cylinder fits\u003c\/h3\u003e\n\u003cp\u003eThis hydraulic cylinder fits the lift models below. Click a model to open its visual parts breakdown — the exploded drawing with every part numbered, so you can confirm this is the right part for your exact lift before you order.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003ca href=\"https:\/\/store.autoliftserv.com\/pages\/parts-lookup#mfr=challenger\u0026amp;model=44050\" style=\"color:#0b5a9c;text-decoration:underline;\"\u003e44050\u003c\/a\u003e — see the exploded parts breakdown for this lift\u003c\/li\u003e\n  \u003cli\u003e\n\u003ca href=\"https:\/\/store.autoliftserv.com\/pages\/parts-lookup#mfr=challenger\u0026amp;model=44060\" style=\"color:#0b5a9c;text-decoration:underline;\"\u003e44060\u003c\/a\u003e — see the exploded parts breakdown for this lift\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\n\u003ch3\u003eRelated parts for this lift\u003c\/h3\u003e\n\u003cp\u003eThe parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"\/products\/challenger-aa8040001-skiti-seal-kit-model-44060\" style=\"color:#0b5a9c;text-decoration:underline;\"\u003eChallenger AA8040001-SKITI Seal Kit Model 44060\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\n\u003ch3\u003eReplacing your hydraulic cylinder\u003c\/h3\u003e\n\u003cp\u003eSwapping a hydraulic hose is mostly about relieving pressure first, catching the fluid, routing the new line so it can't rub or pinch, and bleeding the cylinders afterward. Match the new hose to the old for length, inner diameter, and end fittings. Since a hose under pressure will spray if it's cracked or loose, the full walkthrough is worth reading before you start. \u003cstrong\u003eFull step-by-step: \u003ca href=\"https:\/\/autoliftserv.com\/articles\/how-to-replace-a-2-post-lift-cylinder\/\" style=\"color:#0b5a9c;text-decoration:underline;\"\u003ehow to replace a 2-post lift cylinder\u003c\/a\u003e.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003ch3\u003eFind the right part for your lift\u003c\/h3\u003e\n\u003cp\u003eThe surest way to get the right part is to work from your lift's own breakdown. \u003ca href=\"https:\/\/store.autoliftserv.com\/pages\/parts-lookup#mfr=challenger\" style=\"color:#0b5a9c;text-decoration:underline;\"\u003eopen our Challenger parts lookup\u003c\/a\u003e, choose your model, and every part is mapped on the drawing with its number and price. If you cannot find the model plate, \u003ca href=\"https:\/\/autoliftserv.com\/articles\/how-to-find-car-lift-model-number\/\" style=\"color:#0b5a9c;text-decoration:underline;\"\u003eour guide to finding your model number\u003c\/a\u003e explains where each lift type hides it, and our phone line is open if you want a hand.\u003c\/p\u003e\n\n\u003ch3\u003eSigns of a hydraulic problem\u003c\/h3\u003e\n\u003cp\u003eListen to the power unit. A pump that whines, cavitates, or takes longer than it used to reach full height is low on fluid, pulling air past a suction seal, or wearing out. A motor that hums but won't turn, trips the breaker, or smells hot has an electrical fault or a seized pump. Time a full raise and compare it to how the lift used to run.\u003c\/p\u003e\n\n\u003ch3\u003eParts commonly replaced at the same time\u003c\/h3\u003e\n\u003cp\u003ePlan the whole repair, not just the one part. Cylinders, seals, hoses, and fittings share a pressure system and a service interval, so replacing the obvious failure without the worn companions just sets up the next leak. Give us your model and serial and we will assemble the complete hydraulic kit.\u003c\/p\u003e\n\n\u003ch3\u003eHydraulic fluid\u003c\/h3\u003e\n\u003cp\u003eThe usual fill is \u003cstrong\u003eISO-32\u003c\/strong\u003e hydraulic oil, with some legacy lifts running \u003cstrong\u003eDexron ATF\u003c\/strong\u003e; confirm which your lift uses before topping off and keep the two separate. Bleed after filling and check the level again once the air is out — and see your manual for the exact capacity, which is model-specific.\u003c\/p\u003e\n\n\u003ch3\u003eSafety notes\u003c\/h3\u003e\n\u003cp\u003eClean matters as much as tight in a hydraulic job — a speck of grit through a valve or seal will cost you the repair twice. Cap ports the instant a line is open, use the correct oil, bleed thoroughly, and leak-check at full pressure. Always set the lift on its locks before working underneath it.\u003c\/p\u003e\n\n\u003ch3\u003eBefore you order\u003c\/h3\u003e\n\u003cp\u003eGet the details right up front: model, serial, hose lengths, fitting types, and power-unit voltage where it applies. If the cylinder is only weeping, a seal kit is often the better call. Order the oil you will need for the refill at the same time, and we will verify fit before anything leaves the shelf.\u003c\/p\u003e\n\n\u003ch3\u003eCheck your lift's serial before ordering\u003c\/h3\u003e\n\u003cp\u003eThe most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so \"it fits my lift model\" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift.\u003c\/p\u003e\n\u003cp\u003eCan't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week.\u003c\/p\u003e\n\n\u003ch3\u003eWhy buy your Challenger hydraulic cylinder from Auto Lift Services\u003c\/h3\u003e\n\u003cp\u003eWe install, inspect, and repair Challenger lifts every week — the AA8040001 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call \u003ca href=\"tel:8006749302\" style=\"color:#0b5a9c;text-decoration:underline;\"\u003e800-674-9302\u003c\/a\u003e — and every part ships genuine, no aftermarket substitution unless you ask for it.\u003c\/p\u003e\n\n\u003c!-- als-scaleup-v3 --\u003e","brand":"Challenger","offers":[{"title":"Default Title","offer_id":47704598118653,"sku":"AA8040001","price":38330.2,"currency_code":"USD","in_stock":true}],"url":"https:\/\/store.autoliftserv.com\/products\/challenger-aa8040001-cylinder-mdl-44060-8-bore","provider":"Automotive Lift Services","version":"1.0","type":"link"}