The Rotary 14427 replacement hardware is the direct replacement for the Rotary lift it came off of. Cross-referenced as ALS-7519-28, it is the genuine Rotary part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Rotary replacement hardware from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-7519-28
- Brand: Rotary
- Type: Genuine OEM replacement hardware
Nobody budgets for a washer. That is exactly how a bay ends up dead for three days — the big components get stocked and scheduled, and then the lift goes down over a pin, a clip, or a spring that nobody thought to have on the shelf. Hardware is the highest-leverage inventory in lift maintenance: the unit cost is trivial, the failure mode is a stopped bay, and the lead time is the same freight wait as any other part. When you order the hardware that failed, order its twin on the other side of the lift too — both sides carry the same hours, so the second failure is already scheduled whether you planned for it or not.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
Not sure this fits? Here's how to check
Pull the number off your lift's model plate first — model and serial both. Manufacturers run mid-cycle revisions that keep the model name but change hardware, so two lifts with the same name on the column can take different parts. The serial is what removes the guesswork.
Second check: compare the old part against this listing before you order. Length, mounting pattern, and thread sizes tell most of the story. If anything doesn't line up, or if the old part is too worn or broken to measure, call us with photos — we work on these lifts every week and can usually confirm fit from a picture and the lift's serial faster than you can dig through a parts diagram.
Check the mirror position of whatever failed. Lifts are symmetric machines: the same pin, spring, or bushing exists on the other column or the other end of the crossbeam, with identical hours on it. If one side measured worn, the other side is close behind, and the labor is already paid while the lift is apart. Also inspect the hardware you had to remove for access — disturbed fasteners deserve a look before reuse.
Waiting on a hardware part is not a reason to run the lift without it. A lift missing a retaining clip or running a known-broken spring is out of service until the part arrives — the couple of days of patience is cheaper than what an unretained pin lets go of.
Why buy your Rotary replacement hardware from Auto Lift Services
We install, inspect, and repair Rotary lifts every week — the ALS-7519-28 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine Rotary — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this 14427 spring pin
Every order for the 14427 spring pin starts with a fitment confirmation. Two lifts of the same model can carry subtle revisions between production years, and a component that fits a rev-A lift may not fit a rev-B lift built two years later. Before your card is charged we verify the piece against the parts breakdown for your specific lift serial number. That five-minute step is the difference between the part arriving and being installed the same afternoon versus the wrong piece showing up and the shop losing a day of billable work.
Technical specification & installation notes
Torque and installation notes for this component follow the manufacturer's service manual. Where a torque value is called out, use a calibrated torque wrench and follow the tightening sequence the manual publishes for that fastener location — many lift assemblies require star-pattern or crosswise tightening to distribute load evenly. Skipping that step is one of the most common reasons a correctly-sourced 14427 spring pin still ends up needing to be re-serviced within a year. Our tech line at 800-674-9302 will walk your installer through the procedure if the shop does not have the current service manual on hand.
Shipping & ordering
Shipping runs 3-5 business days on standard ground to the lower 48 states. Expedited overnight and two-day options are available; call 800-674-9302 before ordering to quote expedited freight. We stock the 14427 spring pin in Iowa and ship same-day for orders confirmed before 2 PM Central. Orders that come in later than that or on a Friday afternoon pick up on the next business day. A tracking number gets emailed to the address on the order the moment the package leaves our dock.
Warranty coverage
Every 14427 spring pin sold through Automotive Lift Services carries a one-year manufacturer-defect warranty. If it fails within that window due to a defect in material or workmanship, we replace it at no charge. Damage from improper installation, use outside the lift's rated capacity, side-loading, or modifications to the parent lift are not covered. The warranty is documented on your original order receipt — retain that record for the coverage period. To submit a warranty claim, contact us with the order number and a photo of the failure at [email protected].
Cross-reference & fitment
Cross-reference on the 14427 spring pin is straightforward: match the OEM part number from the lift's parts breakdown against the number on your original invoice. If the numbers match, the component fits. If your lift's parts breakdown lists a superseded or alternate number, we accept the superseded value on the phone as confirmation of fit. When a manufacturer has issued a running change during production, we track the change in our catalog so ordering by the older number automatically pulls the current-spec replacement.
Questions about the 14427 spring pin? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
1/4" x 1-1/2" Spring Pin Stainless - Rotary - 14427
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.