The BendPak ALS-7479-55-4 is the direct-replacement lift arm pad for the BendPak lift it came off of — the genuine part, same fit and same working specification as the one already on your lift. Ordering the BendPak lift arm pad from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.

Specifications

• Part number: ALS-7479-55-4
• Brand: BendPak
• Type: Genuine OEM lift arm pad

Structural parts fail by deforming and by cracking. A rubber arm pad crushes flat and stops gripping; an adapter's lip bends until it won't seat on a pinch weld; a pin hole wallows out egg-shaped from years of load reversal; a weld on an arm or carriage starts a hairline crack. None of these announce themselves with a leak or a noise — you find them by looking, before they let a car slip.

Related parts for this lift

The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.

• Bend Pak 5215250 Adapter with Pad XPR Models
• Bend Pak 5174006p 5715016-4 RUBBER ARM PAD FOR XPR-18C (SET OF 4)
• Bend Pak 35mm Pin Adapter and Pad Assy GM Trucks 2019+ (1)
• Bend Pak 60mm Pin Adapter and Pad Assy GM Trucks 2019+ (1)
• Bend Pak 5174006p 5715016 Rubber Arm Pad for XPR-18C
• Bend Pak 5215702 5174006 Frame Adapter w/Pad XPR-10 models

Replacing your lift arm pad

Carriage or arm work is heavier structural repair — pins, retainers, slide blocks, and load-bearing welds all have to go back sound and correctly torqued. Photograph the assembly before you take it apart, and confirm nothing rocks or has play when it's back together. Since this is the steel carrying the vehicle, the full walkthrough is worth following start to finish. Full step-by-step: how to replace car lift arm pads.

Find the right part for your lift

If you are not sure this part matches your setup, the fastest check is the visual breakdown: open our parts lookup, pick your model, and match your part against the drawing where every item is numbered. Can't read the model plate? our guide to finding your model number shows exactly where it lives on each lift type, and we are a phone call away if you would rather have us confirm it.

Signs this part is worn out

Look at adapter lips and cradles. The lip that hooks a pinch weld or the cradle that cups a frame rail has to be straight and square to seat. A bent, mushroomed, or spread lip won't sit flat and lets the vehicle load a corner or slip. Set the adapter on a flat surface and check it doesn't rock — a bent adapter is a cheap part that can drop a car.

Parts commonly replaced at the same time

The parts near this one share its job and its wear — pads, adapters, swivel pins, retaining hardware. Doing them together restores an even, secure grip on the vehicle and saves reopening the job later. Give us your model and serial and we will match the complete set.

Safety notes

A lift's contact and locating parts do quiet, critical work — holding a vehicle exactly where it belongs. Crushed pads, bent lips, and elongated holes all erode that hold. Replace worn structural parts promptly, torque mounting hardware to spec, and never load a lift onto a contact point you can see is compromised.

Before you order

Order structural parts by model and serial and in the right quantity — a single fresh pad among three flat ones does not help much. Match the part's shape and mount to the original, and add the mounting hardware if it is worn. We will confirm the correct version for your lift.

Check your lift's serial before ordering

The most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so "it fits my lift model" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift.

Can't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week.

Why buy your BendPak lift arm pad from Auto Lift Services

We install, inspect, and repair BendPak lifts every week — the ALS-7479-55-4 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302 — and every part ships genuine, no aftermarket substitution unless you ask for it.