The BendPak 5210240 safety latch is the direct replacement for the BendPak lift it came off of. This is the genuine BendPak part — same fit and same working specification as the one already on your lift. Ordering the BendPak safety latch from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.

Specifications

• Part number: 5210240
• Brand: BendPak
• Type: Genuine OEM safety latch
• Fits: GP-7-150, GP-7LC, GP-7LCS

Lock ladders and pawls are matched geometry — the tooth pitch, the nose angle, and the mounting have to suit the specific lift. A ladder that almost fits will let the pawl sit shallow on the tooth, which is worse than obvious because it looks engaged and isn't. Match restraint parts to the actual lift model and column, not a close-enough substitute, because the whole point of the part is that it holds under full load.

Locks don't work in isolation — they depend on the release mechanism and the leveling of the lift. The lock-release cable or air cylinder pulls all pawls at once so the lift comes down even; if the lift isn't level, one pawl loads before the others and wears first. So when locks click unevenly, the cause can be the ladders, the pawls, the release, or stretched cables. Diagnose the set, not just the noisy corner.

What lifts this safety latch fits

This safety latch fits the lift models below. Click a model to open its visual parts breakdown — the exploded drawing with every part numbered, so you can confirm this is the right part for your exact lift before you order.

• GP-7-150
• GP-7LC
• GP-7LCS

Replacing your safety latch

Getting the locks right means the pawl seats deep in the tooth, the spring returns it every time, and all the locks click in unison — nothing shallow, nothing sticking. It's not difficult work, but there's no partial credit on the part that catches a falling car. For that reason the complete procedure is worth reading before you start. Full step-by-step: how to replace a lift lock ladder.

Find the right part for your lift

Not certain this is the exact part your lift needs? Start with your lift's model and serial off the data plate, then open our parts lookup to see the visual parts breakdown for your model — the exploded drawing with every part numbered and priced. If your plate is missing or unreadable, our guide to finding your model number walks through where to find it, or send us a photo and we will identify the lift for you.

Signs the locking system needs attention

Check that the ladder is tight on its mounts. A ladder that has loosened, shifted, or cracked at a bolt hole moves under load, which changes where the pawl lands and can let it slip past a tooth. Grab it and try to move it; there should be no play. Any give at the mounting means the ladder needs re-securing or replacing before the locks can be trusted.

Parts commonly replaced at the same time

Do the whole locking system while it is apart. The companion parts — springs, pawls, release cable — cost little next to the labor of opening the column, and matched hardware is what keeps both sides in sync. Give us your model and we will assemble the complete set.

Safety notes

When a lock stops working right, the whole safety design is compromised. Rounded latch teeth, weak springs, and misadjusted release cables all keep a carriage from seating fully. Service the locking system as a unit, test that both sides engage and release together, and never trust a load to a lock that drags or clicks late.

Before you order

Ordering tip: lock components are model- and vintage-specific, so read the plate before you buy. Since both columns should engage together, plan to service the lock hardware in pairs, and add the release cable if it is frayed. We will confirm the right parts for your production run.

Check your lift's serial before ordering

The most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so "it fits my lift model" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift.

Can't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week.

Why buy your BendPak safety latch from Auto Lift Services

We install, inspect, and repair BendPak lifts every week — the 5210240 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302 — and every part ships genuine, no aftermarket substitution unless you ask for it.