The BendPak 5402256 electrical control component is the direct replacement for the BendPak lift it came off of. This is the genuine BendPak part — same fit and same working specification as the one already on your lift. Ordering the BendPak electrical control component from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: 5402256
- Brand: BendPak
- Type: Genuine OEM electrical control component
A lift motor tells you it's failing before it quits. It hums but won't turn (a dead start capacitor or a seized pump), it starts slow or weak (worn windings or low voltage), it trips the overload after a minute (drawing too much current), or it runs hot and smells of scorched varnish (insulation breaking down). A motor that's tripping, humming, or smelling hot is on its way out.
Electrical wear is about cycles and connections. Every press of the up button makes and breaks a contactor's points, and those points erode a little each time until they no longer pass full current. Loose connections aren't age so much as vibration and heat working a lug loose over the years. A motor's bearings and start capacitor are the parts that clock hours; the switchgear wears by count of starts.
Replacing your electrical control component
Most lift electrical work follows the same order: verify power is off, trace the circuit from source to motor, replace the failed part, then power up and test both operation and the safety stops. Guessing at where in the chain the fault lives wastes time and risks the wrong part. For that reason the full procedure is worth reading first. Not sure on the procedure? Find your lift in our parts lookup or call and we will walk you through it.
Find the right part for your lift
If you are not sure this part matches your setup, the fastest check is the visual breakdown: open our parts lookup, pick your model, and match your part against the drawing where every item is numbered. Can't read the model plate? our guide to finding your model number shows exactly where it lives on each lift type, and we are a phone call away if you would rather have us confirm it.
Signs of an electrical fault
Start at the source and work in. Confirm the breaker is on and not tripped, the disconnect is closed, and voltage is actually present at the lift with a meter — don't assume. A lift that's completely dead is usually upstream: a tripped breaker, a blown fuse, an open disconnect, or a loose feed. Verify power arrives before you condemn anything on the lift itself.
Parts commonly replaced at the same time
Electrical faults often involve more than one component — a failed contactor can take a relay or a switch with it, and worn wiring shows up alongside. While the panel is open, check the companions so you are not back in there next week. Tell us your lift's voltage and phase and we will match the related parts.
Safety notes
Isolate the lift from power before you touch any electrical component — lock the disconnect out if the shop has one. Lift control circuits mix line voltage with low-voltage safety inputs, and a miswire can defeat an overhead shutoff or a lock. If you are not confident on the control system, stop and call for help before something moves unexpectedly.
Before you order
Have the data plate in front of you — model, serial, voltage, phase — before ordering electrical parts. These details decide which relay, switch, or motor fits, and getting them wrong means a return. If the markings on the old component are readable, share them and we will match exactly.
Not sure this fits? Here's how to check
Pull the number off your lift's model plate first — model and serial both. Manufacturers run mid-cycle revisions that keep the model name but change hardware, so two lifts with the same name on the column can take different parts. The serial is what removes the guesswork.
Second check: compare the old part against this listing before you order. Length, mounting pattern, and thread sizes tell most of the story. If anything doesn't line up, or if the old part is too worn or broken to measure, call us with photos — we work on these lifts every week and can usually confirm fit from a picture and the lift's serial faster than you can dig through a parts diagram.
Why buy your BendPak electrical control component from Auto Lift Services
We install, inspect, and repair BendPak lifts every week — the 5402256 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302 — and every part ships genuine, no aftermarket substitution unless you ask for it.
About this bendpak 5402256 off switch
The bendpak 5402256 off switch is a direct-fit replacement engineered to restore original manufacturer performance on the lift model it services. Every piece we ship carries the exact dimensional and material specifications the OEM published for that application. Fitment on this component is critical: it interfaces with adjacent hardware in ways that any deviation from spec can drive premature wear on nearby parts or trigger the lift's mechanical safety systems into an unexpected condition. Shops that source this from us instead of a generic aftermarket substitute consistently report zero fitment issues on first-time installation.
Technical specification & installation notes
Cycle life on this piece depends heavily on operating conditions. In a typical commercial repair shop running 6-10 lifts per day, the bendpak 5402256 off switch should deliver five to eight years of service before showing measurable wear against the OEM inspection specification. In a high-volume tire or alignment shop running 20+ lifts per day per bay, expect service every three to five years. It is designed to be a serviceable component; when it does wear it wears within safe operating margins that trigger visible symptoms — drift, uneven wear, minor leakage — well before failure becomes a safety issue.
Shipping & ordering
Freight covers the continental United States on all standard orders. We ship UPS or FedEx ground for parts under 30 lb; heavier assemblies quote at published carrier rates. International orders on the bendpak 5402256 off switch require a freight quote — email dimensions, weight, and destination country to [email protected] and we return a rate within one business day. Alaska, Hawaii, and US territories quote at published rates and typically take five to ten business days depending on carrier and destination.
Warranty coverage
Return policy on the bendpak 5402256 off switch follows our store-wide standard: all parts sales are final; exchanges only if the piece arrives defective. In the case of a defective delivery, ship the failed piece back to us at your cost, we verify the defect on receipt, and ship a replacement at ours. Wrong-item deliveries where we made the shipping error follow a different path — we reimburse the return shipping cost and cover freight on the correct part. Contact [email protected] with the order number to start either process.
Cross-reference & fitment
Alternate applications for the bendpak 5402256 off switch sometimes exist. Where a common part fits multiple lift models across a manufacturer's catalog, cross-reference sheets show the compatible models explicitly. If you are consolidating parts stock and want to know which of your lifts the piece covers, email the request to [email protected] with a list of the lift models in your bay — we return a compatibility grid showing which lifts accept the replacement and which need a different number.
Questions about the bendpak 5402256 off switch? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
BendPak 5402256 On / Off Switch 2 Hole Assy; All Dst
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.