The BendPak 5545347 replacement hardware is the direct replacement for the BendPak lift it came off of. This is the genuine BendPak part — same fit and same working specification as the one already on your lift. Ordering the BendPak replacement hardware from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: 5545347
- Brand: BendPak
- Type: Genuine OEM replacement hardware
- Fits: BENDPAK-5260096-HD-9, BENDPAK-5260130-PCL-18B, BENDPAK-5260231-SP-7X, BENDPAK-5260330-PCL-18B, BENDPAK-5260331-PCL-18B, BENDPAK-5260333-PCL-18B, BENDPAK-5260512-HDS-14LSXE, BENDPAK-5260519-HDSO-14, BENDPAK-5260520-HDSO14AX, BENDPAK-5260527-HD-9AE, GP-7-150, GP-7LC
On lift hardware, fit is the whole job. A pin is not a rod of roughly the right diameter — it is a specific length, a specific fit in its bore, and a specific way of being retained, whether that is an e-clip groove, a cotter key hole, or a shoulder. A bushing is a precise interference in its housing and a precise clearance on its shaft. Manufacturer-spec hardware carries all of those dimensions; the hardware-aisle stand-in carries some of them, and the missing ones become play, wobble, and premature wear. This is a spec-correct replacement for the assembly it belongs to — it goes in the way the original came out, retained the way the original was retained.
Not sure this fits? Here's how to check
Pull the number off your lift's model plate first — model and serial both. Manufacturers run mid-cycle revisions that keep the model name but change hardware, so two lifts with the same name on the column can take different parts. The serial is what removes the guesswork.
Second check: compare the old part against this listing before you order. Length, mounting pattern, and thread sizes tell most of the story. If anything doesn't line up, or if the old part is too worn or broken to measure, call us with photos — we work on these lifts every week and can usually confirm fit from a picture and the lift's serial faster than you can dig through a parts diagram.
Lay the new piece against the old before installing: length, diameter, groove and hole positions, thread pitch. If the old part is too worn to compare against, check the new part in its bore or against its mate by hand — it should fit the way a machined part fits, snug and smooth, not loose and not forced. Replace the retaining clips and keys while you are there; they are one-use money.
Retention is not optional. A pin without its e-clip, cotter key, or bolt is a pin working its way out under vibration, and what it drops depends on where it lives. If the retainer came off damaged, replace it — never spring a used clip back on and call it held.
Why buy your BendPak replacement hardware from Auto Lift Services
We install, inspect, and repair BendPak lifts every week — the 5545347 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine BendPak — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this bendpak 5545347 washer flat
The bendpak 5545347 washer flat is a direct-fit replacement engineered to restore original manufacturer performance on the lift model it services. Every piece we ship carries the exact dimensional and material specifications the OEM published for that application. Fitment on this component is critical: it interfaces with adjacent hardware in ways that any deviation from spec can drive premature wear on nearby parts or trigger the lift's mechanical safety systems into an unexpected condition. Shops that source this from us instead of a generic aftermarket substitute consistently report zero fitment issues on first-time installation.
Technical specification & installation notes
Technical specification matches the OEM published dimensions to within manufacturing tolerance. When a shop installs the bendpak 5545347 washer flat correctly, the lift returns to factory-rated performance immediately — no break-in period, no cycle-count adjustment required. The lift's safety systems (mechanical locks, hydraulic pressure relief, and electrical interlocks) treat a correctly-installed replacement exactly as they would treat a factory-original component during initial commissioning. That parity is what lets us honor warranty coverage without asking for the lift's full operating history.
Shipping & ordering
Shipping runs 3-5 business days on standard ground to the lower 48 states. Expedited overnight and two-day options are available; call 800-674-9302 before ordering to quote expedited freight. We stock the bendpak 5545347 washer flat in Iowa and ship same-day for orders confirmed before 2 PM Central. Orders that come in later than that or on a Friday afternoon pick up on the next business day. A tracking number gets emailed to the address on the order the moment the package leaves our dock.
Warranty coverage
Return policy on the bendpak 5545347 washer flat follows our store-wide standard: all parts sales are final; exchanges only if the piece arrives defective. In the case of a defective delivery, ship the failed piece back to us at your cost, we verify the defect on receipt, and ship a replacement at ours. Wrong-item deliveries where we made the shipping error follow a different path — we reimburse the return shipping cost and cover freight on the correct part. Contact [email protected] with the order number to start either process.
Cross-reference & fitment
Fitment on the bendpak 5545347 washer flat is verified against the lift serial number when the order comes in. Even inside one manufacturer's catalog, a lift model built in one production year can carry subtle revisions from the same model built two or three years later. Sending us the lift serial number when you place the order — either in the order notes or in a follow-up email — lets us verify the piece against that specific serial's parts list. That five-minute step catches revision mismatches before shipping and prevents the delay of an incorrect delivery.
Questions about the bendpak 5545347 washer flat? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
BendPak 5545347 Washer, M12 X 24MM Flat, Class 8.8
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.