The BendPak 5550032 replacement part is the direct replacement for the BendPak lift it came off of. This is the genuine BendPak part — same fit and same working specification as the one already on your lift. Ordering the BendPak replacement part from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: 5550032
- Brand: BendPak
- Type: Genuine OEM replacement part
Most lift failures do not start with the big components. They start with a part like this one — something small that wore quietly until the load found the weak point. A worn pin lets a sheave wobble, the wobble chews the cable, and now a cheap part has turned into a cable job. A sticking valve, a thinned bushing, a fatigued spring: each one is a few dollars of steel guarding components that cost hundreds. Replacing wear parts on schedule — instead of when they announce themselves — is the cheapest maintenance a lift ever gets, and it is the difference between shops that fix lifts and shops that keep replacing the expensive parts downstream of the cheap one.
Check your lift's serial before ordering
The most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so "it fits my lift model" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift.
Can't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week.
When one wear part is finished, look hard at what it touched. Metal shavings are the tell — where there are shavings, something has been grinding. Check the mating surfaces this part rode against for scoring, ovaled holes, and rounded edges, because a new part installed against a chewed-up mate wears out on an accelerated schedule and takes the blame for it.
Do not put a known-worn part back in because it looks serviceable enough — on a lift, “probably fine” is carrying somebody’s vehicle over somebody’s head. If it was worn enough to remove, it is worn enough to replace.
Why buy your BendPak replacement part from Auto Lift Services
We install, inspect, and repair BendPak lifts every week — the 5550032 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine BendPak — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this bendpak 5550032 ftg npl
Sourcing the correct bendpak 5550032 ftg npl is not the spot a shop wants to gamble. This piece sits inside a load path the lift manufacturer engineered to specific tolerances, and a substitute that looks close but is off by even a small margin can transfer load onto a neighboring component that was not designed for it. We stock this exact part to the OEM specification the original manufacturer publishes, which is why techs who have been through a bad aftermarket cycle keep coming back to us for the same replacement whenever their next need comes up.
Technical specification & installation notes
Technical specification matches the OEM published dimensions to within manufacturing tolerance. When a shop installs the bendpak 5550032 ftg npl correctly, the lift returns to factory-rated performance immediately — no break-in period, no cycle-count adjustment required. The lift's safety systems (mechanical locks, hydraulic pressure relief, and electrical interlocks) treat a correctly-installed replacement exactly as they would treat a factory-original component during initial commissioning. That parity is what lets us honor warranty coverage without asking for the lift's full operating history.
Shipping & ordering
Freight covers the continental United States on all standard orders. We ship UPS or FedEx ground for parts under 30 lb; heavier assemblies quote at published carrier rates. International orders on the bendpak 5550032 ftg npl require a freight quote — email dimensions, weight, and destination country to [email protected] and we return a rate within one business day. Alaska, Hawaii, and US territories quote at published rates and typically take five to ten business days depending on carrier and destination.
Warranty coverage
Consumables and wear parts like this are covered under the manufacturer defect warranty for twelve months. Because the bendpak 5550032 ftg npl is a component that eventually needs replacement in normal operation, warranty coverage specifically addresses failure due to manufacturing defect, not failure due to normal end-of-life wear. Our team can help distinguish between the two on a phone call if there is any question after installation — call 800-674-9302 and describe the failure pattern; we will tell you honestly whether it looks like a warranty case.
Cross-reference & fitment
Cross-reference on the bendpak 5550032 ftg npl is straightforward: match the OEM part number from the lift's parts breakdown against the number on your original invoice. If the numbers match, the component fits. If your lift's parts breakdown lists a superseded or alternate number, we accept the superseded value on the phone as confirmation of fit. When a manufacturer has issued a running change during production, we track the change in our catalog so ordering by the older number automatically pulls the current-spec replacement.
Questions about the bendpak 5550032 ftg npl? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
BendPak 5550032 Ftg NPL-04 NPT Fx 1/4 Quick-connector Coupler, Male; None Spill Design
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.