The BendPak 5550041 hydraulic fitting is the direct replacement for the BendPak lift it came off of. This is the genuine BendPak part — same fit and same working specification as the one already on your lift. Ordering the BendPak hydraulic fitting from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.

Specifications

• Part number: 5550041
• Brand: BendPak
• Type: Genuine OEM hydraulic fitting

The hydraulic side of a lift is a closed loop: the power unit's motor drives a pump that pushes fluid from the reservoir, through a hose and fittings, into a cylinder that does the lifting, while a lowering valve meters it back to tank on the way down. Every part in that loop either moves fluid, holds pressure, or seals it in. When one link weeps or won't hold, the whole lift feels it.

Dirty or wrong fluid quietly wrecks hydraulic parts. Milky oil means water got in and the pump is cavitating; dark, gritty oil means the system is grinding itself and packing the filter with metal. Mixing ISO-32 and ATF, or topping off with whatever's on the shelf, changes the viscosity the pump was built for. Half the "bad cylinder" calls in a shop start as fluid that should have been changed years ago.

Replacing your hydraulic fitting

Most hydraulic repairs share the same discipline: relieve pressure, keep the system clean, replace the part, then bleed the air and verify the lift holds under load. Contaminated fluid or trapped air will undo an otherwise good job. Because these parts keep a vehicle safely in the air, the full procedure is worth following start to finish. Full step-by-step: how to replace a car lift hydraulic hose.

Find the right part for your lift

Not certain this is the exact part your lift needs? Start with your lift's model and serial off the data plate, then open our parts lookup to see the visual parts breakdown for your model — the exploded drawing with every part numbered and priced. If your plate is missing or unreadable, our guide to finding your model number walks through where to find it, or send us a photo and we will identify the lift for you.

Signs of a hydraulic problem

A spongy or bouncy lift under load is air in the system or a failing seal letting pressure bleed past the piston. Bleed the cylinders first; if it's still soft, the piston seal isn't holding. Watch the rise, too — a cylinder that stalls partway or shudders is either low on fluid, sucking air, or scored inside so the seal skips.

Parts commonly replaced at the same time

A hydraulic repair is the right moment to handle the parts that fail alongside this one — seals, o-rings, the hose that feeds it, and fresh oil for the refill. Opening the system twice for parts you could have done together is wasted labor. We will build the seal-and-hose kit for your lift so the repair is complete in one go.

Hydraulic fluid

When you refill, use the right oil: ISO-32 hydraulic fluid on most lifts, or Dexron ATF on some older designs — never a blend of the two. Your installation manual lists the correct capacity for your specific lift, so fill to that spec and re-check the level after you have cycled and bled the system.

Safety notes

Hydraulic parts hold a vehicle in the air on pressure and a column of oil — respect both. Relieve system pressure before you crack any fitting, cap every open port so grit stays out, and bleed the system fully before the lift carries a load. Air in the lines is what causes a lift to drift or drop unexpectedly.

Before you order

Have the data plate in front of you when you order — model, serial, and voltage if it is a power unit. Match hose length and fitting type against the old part, and remember the job includes fresh oil and a full bleed. Not sure whether you need the part or just seals? Call and we will sort it.

Not sure this fits? Here's how to check

Pull the number off your lift's model plate first — model and serial both. Manufacturers run mid-cycle revisions that keep the model name but change hardware, so two lifts with the same name on the column can take different parts. The serial is what removes the guesswork.

Second check: compare the old part against this listing before you order. Length, mounting pattern, and thread sizes tell most of the story. If anything doesn't line up, or if the old part is too worn or broken to measure, call us with photos — we work on these lifts every week and can usually confirm fit from a picture and the lift's serial faster than you can dig through a parts diagram.

Why buy your BendPak hydraulic fitting from Auto Lift Services

We install, inspect, and repair BendPak lifts every week — the 5550041 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302 — and every part ships genuine, no aftermarket substitution unless you ask for it.