The BendPak 5600432 replacement hardware is the direct replacement for the BendPak lift it came off of. This is the genuine BendPak part — same fit and same working specification as the one already on your lift. Ordering the BendPak replacement hardware from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: 5600432
- Brand: BendPak
- Type: Genuine OEM replacement hardware
- Fits: BENDPAK-5260101-XR-12000A
On lift hardware, fit is the whole job. A pin is not a rod of roughly the right diameter — it is a specific length, a specific fit in its bore, and a specific way of being retained, whether that is an e-clip groove, a cotter key hole, or a shoulder. A bushing is a precise interference in its housing and a precise clearance on its shaft. Manufacturer-spec hardware carries all of those dimensions; the hardware-aisle stand-in carries some of them, and the missing ones become play, wobble, and premature wear. This is a spec-correct replacement for the assembly it belongs to — it goes in the way the original came out, retained the way the original was retained.
Check your lift's serial before ordering
The most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so "it fits my lift model" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift.
Can't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week.
Lay the new piece against the old before installing: length, diameter, groove and hole positions, thread pitch. If the old part is too worn to compare against, check the new part in its bore or against its mate by hand — it should fit the way a machined part fits, snug and smooth, not loose and not forced. Replace the retaining clips and keys while you are there; they are one-use money.
Retention is not optional. A pin without its e-clip, cotter key, or bolt is a pin working its way out under vibration, and what it drops depends on where it lives. If the retainer came off damaged, replace it — never spring a used clip back on and call it held.
Why buy your BendPak replacement hardware from Auto Lift Services
We install, inspect, and repair BendPak lifts every week — the 5600432 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine BendPak — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this bendpak 5600432 safety lock
Sourcing the correct bendpak 5600432 safety lock is not the spot a shop wants to gamble. This piece sits inside a load path the lift manufacturer engineered to specific tolerances, and a substitute that looks close but is off by even a small margin can transfer load onto a neighboring component that was not designed for it. We stock this exact part to the OEM specification the original manufacturer publishes, which is why techs who have been through a bad aftermarket cycle keep coming back to us for the same replacement whenever their next need comes up.
Technical specification & installation notes
Cycle life on this piece depends heavily on operating conditions. In a typical commercial repair shop running 6-10 lifts per day, the bendpak 5600432 safety lock should deliver five to eight years of service before showing measurable wear against the OEM inspection specification. In a high-volume tire or alignment shop running 20+ lifts per day per bay, expect service every three to five years. It is designed to be a serviceable component; when it does wear it wears within safe operating margins that trigger visible symptoms — drift, uneven wear, minor leakage — well before failure becomes a safety issue.
Shipping & ordering
Placing an order online is the fastest path — add to cart, check out, done. If the shop needs a purchase order, net-30 terms, or a formal quote for a fleet-service contract, our accounts team handles those via email at [email protected] or by phone at 800-674-9302. Volume pricing on the bendpak 5600432 safety lock kicks in at 10+ pieces on the same order for common wear items. Ask about the volume rate specifically before you check out — many fleet buyers stock 6-12 pieces at a time and the discount is meaningful over that shelf life.
Warranty coverage
Consumables and wear parts like this are covered under the manufacturer defect warranty for twelve months. Because the bendpak 5600432 safety lock is a component that eventually needs replacement in normal operation, warranty coverage specifically addresses failure due to manufacturing defect, not failure due to normal end-of-life wear. Our team can help distinguish between the two on a phone call if there is any question after installation — call 800-674-9302 and describe the failure pattern; we will tell you honestly whether it looks like a warranty case.
Cross-reference & fitment
Fitment on the bendpak 5600432 safety lock is verified against the lift serial number when the order comes in. Even inside one manufacturer's catalog, a lift model built in one production year can carry subtle revisions from the same model built two or three years later. Sending us the lift serial number when you place the order — either in the order notes or in a follow-up email — lets us verify the piece against that specific serial's parts list. That five-minute step catches revision mismatches before shipping and prevents the delay of an incorrect delivery.
Questions about the bendpak 5600432 safety lock? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
BendPak 5600432 Safety Lock Weldment; XR-12000/A
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.