The BendPak 5600468 replacement hardware is the direct replacement for the BendPak lift it came off of. This is the genuine BendPak part — same fit and same working specification as the one already on your lift. Ordering the BendPak replacement hardware from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: 5600468
- Brand: BendPak
- Type: Genuine OEM replacement hardware
Hardware is the easiest category to order wrong, because so much of it looks generic — a pin is a pin until it is an eighth of an inch short and the e-clip groove lands inside the bore. Lift makers change hardware dimensions between production runs without renaming the lift, so the part that fits a given model can split by serial range. Order from your lift’s data tag — model and serial — rather than from the model name or from a lookalike photo. If the tag is gone, the old hardware itself is the spec: measure it, or photograph it next to a tape measure and send it to us, and we will match it before it ships.
Check your lift's serial before ordering
The most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so "it fits my lift model" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift.
Can't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week.
Measure the old part before you order and again against the new part when it arrives: overall length, diameter, groove and cross-hole locations, and thread size on anything threaded. On threaded hardware, run the nut on by hand first — if it fights, check for welding slag or damaged threads and clean them up with a file rather than powering the nut on and wrecking both parts.
Close is not correct on load-bearing hardware. A pin that is slightly undersized hammers its bore oval; a bolt of the wrong grade shears under a load the right one shrugs off. If what arrived does not match what came out, install nothing and call — guessing is the one move with no good outcome.
Why buy your BendPak replacement hardware from Auto Lift Services
We install, inspect, and repair BendPak lifts every week — the 5600468 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine BendPak — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this bendpak 5600468 bas pusher
Every order for the bendpak 5600468 bas pusher starts with a fitment confirmation. Two lifts of the same model can carry subtle revisions between production years, and a component that fits a rev-A lift may not fit a rev-B lift built two years later. Before your card is charged we verify the piece against the parts breakdown for your specific lift serial number. That five-minute step is the difference between the part arriving and being installed the same afternoon versus the wrong piece showing up and the shop losing a day of billable work.
Technical specification & installation notes
Technical specification matches the OEM published dimensions to within manufacturing tolerance. When a shop installs the bendpak 5600468 bas pusher correctly, the lift returns to factory-rated performance immediately — no break-in period, no cycle-count adjustment required. The lift's safety systems (mechanical locks, hydraulic pressure relief, and electrical interlocks) treat a correctly-installed replacement exactly as they would treat a factory-original component during initial commissioning. That parity is what lets us honor warranty coverage without asking for the lift's full operating history.
Shipping & ordering
Shipping runs 3-5 business days on standard ground to the lower 48 states. Expedited overnight and two-day options are available; call 800-674-9302 before ordering to quote expedited freight. We stock the bendpak 5600468 bas pusher in Iowa and ship same-day for orders confirmed before 2 PM Central. Orders that come in later than that or on a Friday afternoon pick up on the next business day. A tracking number gets emailed to the address on the order the moment the package leaves our dock.
Warranty coverage
Every bendpak 5600468 bas pusher sold through Automotive Lift Services carries a one-year manufacturer-defect warranty. If it fails within that window due to a defect in material or workmanship, we replace it at no charge. Damage from improper installation, use outside the lift's rated capacity, side-loading, or modifications to the parent lift are not covered. The warranty is documented on your original order receipt — retain that record for the coverage period. To submit a warranty claim, contact us with the order number and a photo of the failure at [email protected].
Cross-reference & fitment
Alternate applications for the bendpak 5600468 bas pusher sometimes exist. Where a common part fits multiple lift models across a manufacturer's catalog, cross-reference sheets show the compatible models explicitly. If you are consolidating parts stock and want to know which of your lifts the piece covers, email the request to [email protected] with a list of the lift models in your bay — we return a compatibility grid showing which lifts accept the replacement and which need a different number.
Questions about the bendpak 5600468 bas pusher? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
BendPak 5600468 1302 Bas / Bb Pusher Block Weldment
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.