The BendPak 5600890 replacement hardware is the direct replacement for the BendPak lift it came off of. This is the genuine BendPak part — same fit and same working specification as the one already on your lift. Ordering the BendPak replacement hardware from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: 5600890
- Brand: BendPak
- Type: Genuine OEM replacement hardware
- Fits: BENDPAK-5260527-HD-9AE, HD-7500BLX, HD-7P, HD-7PXW, HD-7W, HD-9, HD-9AE, HD-9ST, HD-9SW, HD-9SWX, HD-9XL, HD-9XW
When a lift gets its annual inspection, the hardware is where a trained eye lingers. Inspectors look for exactly the things this bucket of parts is bought to fix: pins with visible slop, sheaves wobbling on worn bushings, copper-colored bushing material creeping out the side of a sheave, lock springs too tired to snap a pawl home, and chains with tight links or visible stretch. Every one of those is a write-up, and every write-up is a bay out of service until the fix is documented. The economics are lopsided: the hardware costs little, the failed inspection costs the downtime, and the difference between the two outcomes is usually a walk-around you can do yourself in ten minutes.
Not sure this fits? Here's how to check
Pull the number off your lift's model plate first — model and serial both. Manufacturers run mid-cycle revisions that keep the model name but change hardware, so two lifts with the same name on the column can take different parts. The serial is what removes the guesswork.
Second check: compare the old part against this listing before you order. Length, mounting pattern, and thread sizes tell most of the story. If anything doesn't line up, or if the old part is too worn or broken to measure, call us with photos — we work on these lifts every week and can usually confirm fit from a picture and the lift's serial faster than you can dig through a parts diagram.
Do the inspector’s hardware pass: grab each sheave and try to wobble it by hand with the load off — real wobble is a worn pin or bushing. Look for bushing material showing at the sides of sheaves. Cycle the locks and watch that every pawl snaps back smartly; a lazy pawl is a spring. Look for bright rub marks and metal dust anywhere parts move against each other.
A lock pawl with a weak or broken return spring can fail to engage while looking perfectly normal from the floor. Anything in the lock train — springs, pins, pawls — gets replaced on condition, immediately, not monitored. The locks are the part of the lift that catches everything else.
Why buy your BendPak replacement hardware from Auto Lift Services
We install, inspect, and repair BendPak lifts every week — the 5600890 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine BendPak — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this bendpak 5600890 tire stop
The bendpak 5600890 tire stop is a direct-fit replacement engineered to restore original manufacturer performance on the lift model it services. Every piece we ship carries the exact dimensional and material specifications the OEM published for that application. Fitment on this component is critical: it interfaces with adjacent hardware in ways that any deviation from spec can drive premature wear on nearby parts or trigger the lift's mechanical safety systems into an unexpected condition. Shops that source this from us instead of a generic aftermarket substitute consistently report zero fitment issues on first-time installation.
Technical specification & installation notes
Technical specification matches the OEM published dimensions to within manufacturing tolerance. When a shop installs the bendpak 5600890 tire stop correctly, the lift returns to factory-rated performance immediately — no break-in period, no cycle-count adjustment required. The lift's safety systems (mechanical locks, hydraulic pressure relief, and electrical interlocks) treat a correctly-installed replacement exactly as they would treat a factory-original component during initial commissioning. That parity is what lets us honor warranty coverage without asking for the lift's full operating history.
Shipping & ordering
Freight covers the continental United States on all standard orders. We ship UPS or FedEx ground for parts under 30 lb; heavier assemblies quote at published carrier rates. International orders on the bendpak 5600890 tire stop require a freight quote — email dimensions, weight, and destination country to [email protected] and we return a rate within one business day. Alaska, Hawaii, and US territories quote at published rates and typically take five to ten business days depending on carrier and destination.
Warranty coverage
Return policy on the bendpak 5600890 tire stop follows our store-wide standard: all parts sales are final; exchanges only if the piece arrives defective. In the case of a defective delivery, ship the failed piece back to us at your cost, we verify the defect on receipt, and ship a replacement at ours. Wrong-item deliveries where we made the shipping error follow a different path — we reimburse the return shipping cost and cover freight on the correct part. Contact [email protected] with the order number to start either process.
Cross-reference & fitment
Cross-reference on the bendpak 5600890 tire stop is straightforward: match the OEM part number from the lift's parts breakdown against the number on your original invoice. If the numbers match, the component fits. If your lift's parts breakdown lists a superseded or alternate number, we accept the superseded value on the phone as confirmation of fit. When a manufacturer has issued a running change during production, we track the change in our catalog so ordering by the older number automatically pulls the current-spec replacement.
Questions about the bendpak 5600890 tire stop? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
BendPak 5600890 Tire Stop Plate Weldment; HD-7/7500/9
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.