The BendPak 5731309 lifting cable is the direct replacement for the BendPak lift it came off of. This is the genuine BendPak part — same fit and same working specification as the one already on your lift. Ordering the BendPak lifting cable from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.

Specifications

• Part number: 5731309
• Brand: BendPak
• Type: Genuine OEM lifting cable
• Fits: BENDPAK-5260096-HD-9, BENDPAK-5260527-HD-9AE, HD-7500BLX, HD-9, HD-973P, HD-973PX, HD-9AE, HD-9ST, HD-9SW, HD-9SWX, HD-9XL, HD-9XW

Cable failure almost never happens all at once. A strand pops here, a groove wears oversize there, a sheave bushing walks out the side, and the cable starts cording where it turns. Left alone, the frayed section keeps losing strands until the day it lets go — usually with weight on the lift. That is the whole reason these tension parts get inspected and swapped on a schedule instead of run to failure.

Rust is the quiet killer of lift cable. A shop in a salt-belt climate, or a lift that sat in a damp corner for a few years, loses cable to corrosion long before it ever wears out mechanically. Surface rust you can live with; rust that has eaten into the strands or frozen a sheave bushing you cannot. Once the steel is pitting under the outer wires, the rated strength is already gone.

What lifts this lifting cable fits

This lifting cable fits the lift models below. Click a model to open its visual parts breakdown — the exploded drawing with every part numbered, so you can confirm this is the right part for your exact lift before you order.

• BENDPAK-5260096-HD-9
• BENDPAK-5260527-HD-9AE
• HD-7500BLX
• HD-9
• HD-973P
• HD-973PX
• HD-9AE
• HD-9ST
• HD-9SW
• HD-9SWX

Replacing your lifting cable

A lock-release cable replacement is a quick job with a safety payoff: the new cable has to pull every pawl out of its ladder at the same time so the lift descends level. Route it, set the tension, and cycle the lift watching that all the locks release together. The exact routing and adjustment vary by lift, so walk through the full procedure before you rely on it. Full step-by-step: how to replace 2-post lift cables.

Find the right part for your lift

If you are not sure this part matches your setup, the fastest check is the visual breakdown: open our parts lookup, pick your model, and match your part against the drawing where every item is numbered. Can't read the model plate? our guide to finding your model number shows exactly where it lives on each lift type, and we are a phone call away if you would rather have us confirm it.

Signs a cable or sheave is worn out

Watch the lift work, not just the parts. If one lock clicks noticeably before the others on the way up, or the lift lands one corner first on the way down, a cable has stretched or a sheave is dragging. Then inspect the suspect cable end to end for broken strands and the sheaves for groove wear. A lift that won't equalize is telling you a tension part is going.

Parts commonly replaced at the same time

The parts around this one tend to wear on the same clock — companion cables, the sheaves they run over, and the hardware that retains them. Bundling them into one order and one repair saves a second teardown. We keep the cross-references for your lift, so one call gets the whole set right.

Safety notes

Cables stretch and sheaves wear on a schedule; failures happen when someone stretches that schedule. Change tension parts as a set, confirm each cable is seated in every sheave before you tension it, and keep the safety locks in the loop the entire time you work — they are what stands between the load and the floor if something slips.

Before you order

Order the whole wear set, not just the one that failed — cables and sheaves age together, and doing them in one visit is cheaper than two. Have your model and serial ready so we can pull the right lengths and fittings for your lift, and ask if you want the companion parts added.

Check your lift's serial before ordering

The most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so "it fits my lift model" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift.

Can't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week.

Why buy your BendPak lifting cable from Auto Lift Services

We install, inspect, and repair BendPak lifts every week — the 5731309 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302 — and every part ships genuine, no aftermarket substitution unless you ask for it.