The Challenger EQ10-IOM-Q installation and operation manual is the direct replacement for the Challenger lift it came off of. This is the genuine Challenger part — same fit and same working specification as the one already on your lift. Ordering the Challenger installation and operation manual from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.

Specifications

• Part number: EQ10-IOM-Q
• Brand: Challenger
• Type: Genuine OEM installation and operation manual

Not every part on a lift lifts — a lot of them support the ones that do. Airlines feed the lock releases, decals mark capacities and controls, hardware holds the assembly together, and the manual carries the specs and the procedure. They're easy to overlook precisely because they're not the cylinder or the cables, but a lift missing its safety decals, its air supply, or the right fastener isn't a complete, safe lift.

Replacing your installation and operation manual

Sorting out the air supply — compressor, regulator, moisture trap — is about delivering clean, steady pressure to the lock system on demand. Set the regulator, drain the trap, and confirm the pressure holds while the locks cycle. The step-by-step guide lays out the settings and checks. Not sure on the procedure? Find your lift in our parts lookup or call and we will walk you through it.

Find the right part for your lift

Not certain this is the exact part your lift needs? Start with your lift's model and serial off the data plate, then open our Challenger parts lookup to see the visual parts breakdown for your model — the exploded drawing with every part numbered and priced. If your plate is missing or unreadable, our guide to finding your model number walks through where to find it, or send us a photo and we will identify the lift for you.

Signs it's time to replace it

For hardware, check tightness, grade, and corrosion. Go around the fasteners and confirm nothing has backed out, stripped, or gone missing, especially on load-bearing and anchor points. Look for the right grade markings on structural bolts and for rust that has weakened a fastener. A bolt you can turn by hand, a stripped thread, or a missing lock feature is a defect — retorque or replace before it works fully loose.

Parts commonly replaced at the same time

Since you are already ordering, tell us your lift and we will point out what else it commonly needs — related hardware, safety labeling, accessories rated for your model. Consolidating into one order is cheaper and simpler than piecing it together over several. We keep the breakdown for your lift on hand.

Safety notes

The little parts round out a safe, compliant lift. Use the correct component for your model, keep the required labeling in place and readable, and follow the manufacturer's install notes. If you are not sure which version your lift takes, a quick call saves a wrong order and a second trip up the ladder.

Before you order

Before ordering, confirm your lift's model and serial so we can match the correct version — even simple parts have revisions. If you are replacing a decal set or an accessory, tell us the model and we will make sure you get the one specified for your lift rather than a near-miss.

Confirm this is the right part before you order

Lift manufacturers revise parts mid-production without changing the model name, so the same lift bought two years apart can take two different revisions of the same component. Before you order, find the model plate on the lift — on most 2-post lifts it rides on one of the columns at eye level, on 4-post lifts it is usually on a column or the power-unit side runway — and note the full model number and serial. The serial dates the lift to a production run, and that is what decides which revision fits.

If the plate is painted over or missing, take a photo of the part you are replacing next to a tape measure and send it to us. Between the dimensions, the mounting pattern, and what lift it came off of, we can almost always identify the exact part before you spend money on the wrong one.

Why buy your Challenger installation and operation manual from Auto Lift Services

We install, inspect, and repair Challenger lifts every week — the EQ10-IOM-Q is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302 — and every part ships genuine, no aftermarket substitution unless you ask for it.