The Challenger SR10-001 is the direct-replacement lift adapter for the Challenger lift it came off of — the genuine part, same fit and same working specification as the one already on your lift. Ordering the Challenger lift adapter from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.

Specifications

• Part number: SR10-001
• Brand: Challenger
• Type: Genuine OEM lift adapter

These parts wear from repetition and from abuse. A pad that lifts twenty cars a day compresses and tears far sooner than one that works part-time. But abuse ages them faster than hours ever will: an adapter dropped and bent, an arm hit by a car pulling out, a carriage overloaded past its rating. Rubber pads are consumables that need regular replacement; steel parts last until something bends or cracks them.

Related parts for this lift

The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.

• Challenger SR10-001 Two Position Adapter Blocks Steel with Rubber Pads Set of 4) for Srm10

Replacing your lift adapter

Replacing an adapter is usually drop-in, but the fit is everything: the new adapter has to reach the correct height, seat square on the pinch weld or frame, and clear the rocker. Set it in place and load-test it before trusting a car to it. The step-by-step guide covers how to confirm it's seating right. Not sure on the procedure? Find your lift in our parts lookup or call and we will walk you through it.

Find the right part for your lift

Want to be sure before you buy? Pull the model and serial off your lift's plate and open our Challenger parts lookup to open the exploded parts breakdown for your model — find your part on the drawing and you know it fits. New to finding your model number? our guide to finding your model number covers it, or send a photo of the plate and we will read it for you.

Signs this part is worn out

Check the arms for straightness and the pins for wear. Sight down each arm for a bend from being backed into or overloaded, and check that the telescoping sections slide without excessive slop. Worn arm pins and retainers let the arm lift or rotate under load. An arm that's bent, or that flops on a worn pin, isn't holding the car where you set it.

Parts commonly replaced at the same time

Order structural parts in the set they belong to. A single fresh pad among three flat ones does not restore even support, and the pins and hardware around a worn part are usually due too. We keep the right versions for your lift and can assemble the full contact-point kit in one order.

Safety notes

Do not overlook the structural wear items just because they are simple. A worn arm pad or a cracked ramp weld can let a vehicle walk or drop, and they fail quietly until the day they do not. Inspect contact points every service and replace anything crushed, cracked, or bent before the next lift.

Before you order

A little prep saves a wrong part: confirm model and serial, count how many you need, and match the mounting against what came off. Pads and adapters wear as a group, so ordering the set is usually the smart move. Ask about the companion hardware while you are at it.

Not sure this fits? Here's how to check

Pull the number off your lift's model plate first — model and serial both. Manufacturers run mid-cycle revisions that keep the model name but change hardware, so two lifts with the same name on the column can take different parts. The serial is what removes the guesswork.

Second check: compare the old part against this listing before you order. Length, mounting pattern, and thread sizes tell most of the story. If anything doesn't line up, or if the old part is too worn or broken to measure, call us with photos — we work on these lifts every week and can usually confirm fit from a picture and the lift's serial faster than you can dig through a parts diagram.

Why buy your Challenger lift adapter from Auto Lift Services

We install, inspect, and repair Challenger lifts every week — the SR10-001 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302 — and every part ships genuine, no aftermarket substitution unless you ask for it.