The Challenger TCS4-07-05-00 lifting cable is the direct replacement for the Challenger lift it came off of. This is the genuine Challenger part — same fit and same working specification as the one already on your lift. Ordering the Challenger lifting cable from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.

Specifications

• Part number: TCS4-07-05-00
• Brand: Challenger
• Type: Genuine OEM lifting cable
• Fits: Q4P07, Q4P09

Cable length and end fittings are what make a tension part fit, and they vary more than people expect. Older asymmetric lifts ran a long cable and a short cable; some columns use a threaded stud end, others a button or wedge. Order by the lift's actual routing, not a guess, because a cable that's an inch off or ends in the wrong fitting won't tension right no matter how you adjust it.

A cable is only as good as the sheave it rides. The two parts wear as a system: a grooved or wobbling sheave chews the cable, and a corded cable grinds a fresh sheave. That's why techs who pull a lift apart for one usually replace both, along with the small lock-release cable that trips the pawls. Swapping a cable onto worn sheaves just starts the failure clock over again.

What lifts this lifting cable fits

This lifting cable fits the lift models below. Click a model to open its visual parts breakdown — the exploded drawing with every part numbered, so you can confirm this is the right part for your exact lift before you order.

• Q4P07 — see the exploded parts breakdown for this lift
• Q4P09 — see the exploded parts breakdown for this lift

Related parts for this lift

The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.

• Challenger TCS4-04-03-00 Sheave Assembly
• Challenger TCS4-04-14 Sheave Guard
• Challenger TCS4-07-02 Runway Sheave Spacer - Short
• Challenger TCS4-07-03 Runway Sheave Spacer - Tall
• Challenger TCS4-07-04-00 Sheave Pin Assembly
• Challenger TCS4-11-01 Driver Side Rear Cable

Replacing your lifting cable

A lock-release cable replacement is a quick job with a safety payoff: the new cable has to pull every pawl out of its ladder at the same time so the lift descends level. Route it, set the tension, and cycle the lift watching that all the locks release together. The exact routing and adjustment vary by lift, so walk through the full procedure before you rely on it. Full step-by-step: how to replace 2-post lift cables.

Find the right part for your lift

Not certain this is the exact part your lift needs? Start with your lift's model and serial off the data plate, then open our Challenger parts lookup to see the visual parts breakdown for your model — the exploded drawing with every part numbered and priced. If your plate is missing or unreadable, our guide to finding your model number walks through where to find it, or send us a photo and we will identify the lift for you.

Signs a cable or sheave is worn out

Pay attention to the cable ends and fittings. The threaded stud where the adjusting nut rides is a common failure point — look for stretched, necked-down threads and cracks at the swage where the fitting is crimped to the cable. If the swage shows any gap or the wires are pulling out of the fitting, the cable is finished regardless of how good the middle looks.

Parts commonly replaced at the same time

The parts around this one tend to wear on the same clock — companion cables, the sheaves they run over, and the hardware that retains them. Bundling them into one order and one repair saves a second teardown. We keep the cross-references for your lift, so one call gets the whole set right.

Safety notes

Cables stretch and sheaves wear on a schedule; failures happen when someone stretches that schedule. Change tension parts as a set, confirm each cable is seated in every sheave before you tension it, and keep the safety locks in the loop the entire time you work — they are what stands between the load and the floor if something slips.

Before you order

Order the whole wear set, not just the one that failed — cables and sheaves age together, and doing them in one visit is cheaper than two. Have your model and serial ready so we can pull the right lengths and fittings for your lift, and ask if you want the companion parts added.

Check your lift's serial before ordering

The most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so "it fits my lift model" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift.

Can't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week.

Why buy your Challenger lifting cable from Auto Lift Services

We install, inspect, and repair Challenger lifts every week — the TCS4-07-05-00 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302 — and every part ships genuine, no aftermarket substitution unless you ask for it.