The Weaver 1084718 replacement hardware is the direct replacement for the Weaver lift it came off of. Cross-referenced as ALS-9673-06, it is the genuine Weaver part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Weaver replacement hardware from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-9673-06
- Brand: Weaver
- Type: Genuine OEM replacement hardware
Hardware is where lift failures are born. A pin that has worn oval lets its sheave run crooked; the crooked sheave saws at the cable; and a five-dollar pin has now written a quote for cables and sheaves. Springs lose tension and a lock pawl stops returning. A bushing thins out and the clunk everyone ignores becomes the slop that rounds off the bore it sits in. None of these parts fail dramatically — they just get a little loose, a little rounder, a little weaker, and pass the damage up to whatever they located or supported. Replacing hardware at the first sign of wear is how the expensive parts on a lift get to live out their full lives.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
Check your lift's serial before ordering
The most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so "it fits my lift model" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift.
Can't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week.
When hardware comes out, read it. An ovaled pin means its bore is probably ovaled too — check the hole, not just the pin. A stretched spring means something was binding for it to fight. Bright metal dust around a bushing or bearing means it has been grinding, so inspect what it rides in. New hardware in a worn bore is a short-term repair with a long-term invoice.
Never reuse a bent pin, a stretched spring, or a mushroomed piece of hardware because it still technically fits — and never substitute generic hardware-store fasteners for load-bearing lift hardware. Grade and dimensions exist for a reason on a machine that holds vehicles in the air.
Why buy your Weaver replacement hardware from Auto Lift Services
We install, inspect, and repair Weaver lifts every week — the ALS-9673-06 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine Weaver — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this 1084718 door support
Every order for the 1084718 door support starts with a fitment confirmation. Two lifts of the same model can carry subtle revisions between production years, and a component that fits a rev-A lift may not fit a rev-B lift built two years later. Before your card is charged we verify the piece against the parts breakdown for your specific lift serial number. That five-minute step is the difference between the part arriving and being installed the same afternoon versus the wrong piece showing up and the shop losing a day of billable work.
Technical specification & installation notes
Technical specification matches the OEM published dimensions to within manufacturing tolerance. When a shop installs the 1084718 door support correctly, the lift returns to factory-rated performance immediately — no break-in period, no cycle-count adjustment required. The lift's safety systems (mechanical locks, hydraulic pressure relief, and electrical interlocks) treat a correctly-installed replacement exactly as they would treat a factory-original component during initial commissioning. That parity is what lets us honor warranty coverage without asking for the lift's full operating history.
Shipping & ordering
Freight covers the continental United States on all standard orders. We ship UPS or FedEx ground for parts under 30 lb; heavier assemblies quote at published carrier rates. International orders on the 1084718 door support require a freight quote — email dimensions, weight, and destination country to [email protected] and we return a rate within one business day. Alaska, Hawaii, and US territories quote at published rates and typically take five to ten business days depending on carrier and destination.
Warranty coverage
Consumables and wear parts like this are covered under the manufacturer defect warranty for twelve months. Because the 1084718 door support is a component that eventually needs replacement in normal operation, warranty coverage specifically addresses failure due to manufacturing defect, not failure due to normal end-of-life wear. Our team can help distinguish between the two on a phone call if there is any question after installation — call 800-674-9302 and describe the failure pattern; we will tell you honestly whether it looks like a warranty case.
Cross-reference & fitment
Cross-reference on the 1084718 door support is straightforward: match the OEM part number from the lift's parts breakdown against the number on your original invoice. If the numbers match, the component fits. If your lift's parts breakdown lists a superseded or alternate number, we accept the superseded value on the phone as confirmation of fit. When a manufacturer has issued a running change during production, we track the change in our catalog so ordering by the older number automatically pulls the current-spec replacement.
Questions about the 1084718 door support? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
Door Support Pin - Weaver - 1084718
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.