The Rotary FC5301-97 replacement part is the direct replacement for the Rotary lift it came off of. Cross-referenced as ALS-7508-99, it is the genuine Rotary part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Rotary replacement part from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-7508-99
- Brand: Rotary
- Type: Genuine OEM replacement part
- Fits: AR12, AR120EL1, AR120L, AR120S, AR123, AR90, ARO123, CWA90, FLS12, FLS25, SM12, SM120
- Lift type: 4-post lift
Most lift failures do not start with the big components. They start with a part like this one — something small that wore quietly until the load found the weak point. A worn pin lets a sheave wobble, the wobble chews the cable, and now a cheap part has turned into a cable job. A sticking valve, a thinned bushing, a fatigued spring: each one is a few dollars of steel guarding components that cost hundreds. Replacing wear parts on schedule — instead of when they announce themselves — is the cheapest maintenance a lift ever gets, and it is the difference between shops that fix lifts and shops that keep replacing the expensive parts downstream of the cheap one.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
- Wheel Chock - Rotary FC320
- Wheel Stop Assembly - Rotary FC134-13
- Front Cross Member - Rotary FC5302
- Cross Support - Rotary FC217
- Levelling Leg - Rotary FC134-28
- Overhead Limit Bar - Rotary FJ7613-2
Ordering the right revision
Before this goes in the cart, grab two things off your lift: the model number and the serial number, both on the manufacturer's plate. The serial matters more than most people expect — lift makers revise components between production runs without renaming the lift, and the run your serial falls in determines which revision of this part is correct.
If you are working from a failed part rather than a plate, measure what you have and photograph how it mounts. Send that to us along with the lift brand, and we will check it against the same parts breakdowns our own techs use in the field before you commit to the order.
When one wear part is finished, look hard at what it touched. Metal shavings are the tell — where there are shavings, something has been grinding. Check the mating surfaces this part rode against for scoring, ovaled holes, and rounded edges, because a new part installed against a chewed-up mate wears out on an accelerated schedule and takes the blame for it.
Do not put a known-worn part back in because it looks serviceable enough — on a lift, “probably fine” is carrying somebody’s vehicle over somebody’s head. If it was worn enough to remove, it is worn enough to replace.
Why buy your Rotary replacement part from Auto Lift Services
We install, inspect, and repair Rotary lifts every week — the ALS-7508-99 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine Rotary — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this fc5301 slider hole
The fc5301 slider hole is a direct-fit replacement engineered to restore original manufacturer performance on the lift model it services. Every piece we ship carries the exact dimensional and material specifications the OEM published for that application. Fitment on this component is critical: it interfaces with adjacent hardware in ways that any deviation from spec can drive premature wear on nearby parts or trigger the lift's mechanical safety systems into an unexpected condition. Shops that source this from us instead of a generic aftermarket substitute consistently report zero fitment issues on first-time installation.
Technical specification & installation notes
Cycle life on this piece depends heavily on operating conditions. In a typical commercial repair shop running 6-10 lifts per day, the fc5301 slider hole should deliver five to eight years of service before showing measurable wear against the OEM inspection specification. In a high-volume tire or alignment shop running 20+ lifts per day per bay, expect service every three to five years. It is designed to be a serviceable component; when it does wear it wears within safe operating margins that trigger visible symptoms — drift, uneven wear, minor leakage — well before failure becomes a safety issue.
Shipping & ordering
Freight covers the continental United States on all standard orders. We ship UPS or FedEx ground for parts under 30 lb; heavier assemblies quote at published carrier rates. International orders on the fc5301 slider hole require a freight quote — email dimensions, weight, and destination country to [email protected] and we return a rate within one business day. Alaska, Hawaii, and US territories quote at published rates and typically take five to ten business days depending on carrier and destination.
Warranty coverage
Return policy on the fc5301 slider hole follows our store-wide standard: all parts sales are final; exchanges only if the piece arrives defective. In the case of a defective delivery, ship the failed piece back to us at your cost, we verify the defect on receipt, and ship a replacement at ours. Wrong-item deliveries where we made the shipping error follow a different path — we reimburse the return shipping cost and cover freight on the correct part. Contact [email protected] with the order number to start either process.
Cross-reference & fitment
Alternate applications for the fc5301 slider hole sometimes exist. Where a common part fits multiple lift models across a manufacturer's catalog, cross-reference sheets show the compatible models explicitly. If you are consolidating parts stock and want to know which of your lifts the piece covers, email the request to [email protected] with a list of the lift models in your bay — we return a compatibility grid showing which lifts accept the replacement and which need a different number.
Questions about the fc5301 slider hole? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
Slider 1-Hole Version - Rotary FC5301-97
Parts that fit your lift
This Rotary part fits the lift models below. Click your model to see every part that fits it — handy for grabbing the wear items that usually go at the same time (cables, sheaves, pins, locks).
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.