The Rotary FC5706-16 replacement part is the direct replacement for the Rotary lift it came off of. Cross-referenced as ALS-7517-31, it is the genuine Rotary part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Rotary replacement part from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-7517-31
- Brand: Rotary
- Type: Genuine OEM replacement part
- Fits: AR12, AR120EL1, AR120L, AR120S, AR122EL1, AR122EL2, AR122L, AR122S, AR123, AR90, ARO123, CWA90
- Lift type: 4-post lift
We are not a catalog that happens to list lift parts — our field techs install, inspect, and repair automotive lifts every week, and the parts on this site are the ones that come off our own service trucks. That changes what you get with the order. When you are not sure this is the right part, you can send a photo of your lift’s data tag and the failed part and get an answer from someone who has had that exact assembly apart. And when you hit something mid-job that the manual does not cover, the phone gets answered by people who have been under the same lift with the same wrench.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
- Yoke End Cover - Rotary FC5802-18
- Right Runway - Rotary FC136
- Left Runway - Rotary FC137
- Yoke End Cover (Front) - Rotary S130014
- Spacer - Rotary - FC5190-21
- Square Guide Axle Kit - Rotary - FC5412
Check your lift's serial before ordering
The most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so "it fits my lift model" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift.
Can't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week.
The habit our techs are trained into applies here: when you finish a repair, run the lift through full cycles — all the way up, onto the locks, all the way down — and watch and listen the whole way. Leaks, rubbing, scraping, and locks that engage late all show themselves in the first three cycles if you are paying attention, which is a much better time to find them than under the next customer vehicle.
If you get into the job and find more wrong than you expected, stop and reassess rather than improvising a way through — call us if you want a second opinion. Half-finished lift repairs are more dangerous than the original failure, because now the lift looks fixed.
Why buy your Rotary replacement part from Auto Lift Services
We install, inspect, and repair Rotary lifts every week — the ALS-7517-31 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine Rotary — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this fc5706 slider hole
Sourcing the correct fc5706 slider hole is not the spot a shop wants to gamble. This piece sits inside a load path the lift manufacturer engineered to specific tolerances, and a substitute that looks close but is off by even a small margin can transfer load onto a neighboring component that was not designed for it. We stock this exact part to the OEM specification the original manufacturer publishes, which is why techs who have been through a bad aftermarket cycle keep coming back to us for the same replacement whenever their next need comes up.
Technical specification & installation notes
Torque and installation notes for this component follow the manufacturer's service manual. Where a torque value is called out, use a calibrated torque wrench and follow the tightening sequence the manual publishes for that fastener location — many lift assemblies require star-pattern or crosswise tightening to distribute load evenly. Skipping that step is one of the most common reasons a correctly-sourced fc5706 slider hole still ends up needing to be re-serviced within a year. Our tech line at 800-674-9302 will walk your installer through the procedure if the shop does not have the current service manual on hand.
Shipping & ordering
Placing an order online is the fastest path — add to cart, check out, done. If the shop needs a purchase order, net-30 terms, or a formal quote for a fleet-service contract, our accounts team handles those via email at [email protected] or by phone at 800-674-9302. Volume pricing on the fc5706 slider hole kicks in at 10+ pieces on the same order for common wear items. Ask about the volume rate specifically before you check out — many fleet buyers stock 6-12 pieces at a time and the discount is meaningful over that shelf life.
Warranty coverage
Consumables and wear parts like this are covered under the manufacturer defect warranty for twelve months. Because the fc5706 slider hole is a component that eventually needs replacement in normal operation, warranty coverage specifically addresses failure due to manufacturing defect, not failure due to normal end-of-life wear. Our team can help distinguish between the two on a phone call if there is any question after installation — call 800-674-9302 and describe the failure pattern; we will tell you honestly whether it looks like a warranty case.
Cross-reference & fitment
Alternate applications for the fc5706 slider hole sometimes exist. Where a common part fits multiple lift models across a manufacturer's catalog, cross-reference sheets show the compatible models explicitly. If you are consolidating parts stock and want to know which of your lifts the piece covers, email the request to [email protected] with a list of the lift models in your bay — we return a compatibility grid showing which lifts accept the replacement and which need a different number.
Questions about the fc5706 slider hole? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
Slider 2-Hole Version (pictured) - Rotary FC5706-16
Parts that fit your lift
This Rotary part fits the lift models below. Click your model to see every part that fits it — handy for grabbing the wear items that usually go at the same time (cables, sheaves, pins, locks).
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.