Hinge Pin Lock Ring - Nussbaum - 10.118 — a direct-fit replacement replacement hardware. Ordering the replacement hardware from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-7451-32
- Type: Genuine OEM replacement hardware
On lift hardware, fit is the whole job. A pin is not a rod of roughly the right diameter — it is a specific length, a specific fit in its bore, and a specific way of being retained, whether that is an e-clip groove, a cotter key hole, or a shoulder. A bushing is a precise interference in its housing and a precise clearance on its shaft. Manufacturer-spec hardware carries all of those dimensions; the hardware-aisle stand-in carries some of them, and the missing ones become play, wobble, and premature wear. This is a spec-correct replacement for the assembly it belongs to — it goes in the way the original came out, retained the way the original was retained.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
Not sure this fits? Here's how to check
Pull the number off your lift's model plate first — model and serial both. Manufacturers run mid-cycle revisions that keep the model name but change hardware, so two lifts with the same name on the column can take different parts. The serial is what removes the guesswork.
Second check: compare the old part against this listing before you order. Length, mounting pattern, and thread sizes tell most of the story. If anything doesn't line up, or if the old part is too worn or broken to measure, call us with photos — we work on these lifts every week and can usually confirm fit from a picture and the lift's serial faster than you can dig through a parts diagram.
Lay the new piece against the old before installing: length, diameter, groove and hole positions, thread pitch. If the old part is too worn to compare against, check the new part in its bore or against its mate by hand — it should fit the way a machined part fits, snug and smooth, not loose and not forced. Replace the retaining clips and keys while you are there; they are one-use money.
Retention is not optional. A pin without its e-clip, cotter key, or bolt is a pin working its way out under vibration, and what it drops depends on where it lives. If the retainer came off damaged, replace it — never spring a used clip back on and call it held.
Why buy your replacement hardware from Auto Lift Services
We install, inspect, and repair automotive lifts every week — the ALS-7451-32 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine OEM — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this 10118 hinge pin
The 10118 hinge pin is a direct-fit replacement engineered to restore original manufacturer performance on the lift model it services. Every piece we ship carries the exact dimensional and material specifications the OEM published for that application. Fitment on this component is critical: it interfaces with adjacent hardware in ways that any deviation from spec can drive premature wear on nearby parts or trigger the lift's mechanical safety systems into an unexpected condition. Shops that source this from us instead of a generic aftermarket substitute consistently report zero fitment issues on first-time installation.
Technical specification & installation notes
Technical specification matches the OEM published dimensions to within manufacturing tolerance. When a shop installs the 10118 hinge pin correctly, the lift returns to factory-rated performance immediately — no break-in period, no cycle-count adjustment required. The lift's safety systems (mechanical locks, hydraulic pressure relief, and electrical interlocks) treat a correctly-installed replacement exactly as they would treat a factory-original component during initial commissioning. That parity is what lets us honor warranty coverage without asking for the lift's full operating history.
Shipping & ordering
Shipping runs 3-5 business days on standard ground to the lower 48 states. Expedited overnight and two-day options are available; call 800-674-9302 before ordering to quote expedited freight. We stock the 10118 hinge pin in Iowa and ship same-day for orders confirmed before 2 PM Central. Orders that come in later than that or on a Friday afternoon pick up on the next business day. A tracking number gets emailed to the address on the order the moment the package leaves our dock.
Warranty coverage
Return policy on the 10118 hinge pin follows our store-wide standard: all parts sales are final; exchanges only if the piece arrives defective. In the case of a defective delivery, ship the failed piece back to us at your cost, we verify the defect on receipt, and ship a replacement at ours. Wrong-item deliveries where we made the shipping error follow a different path — we reimburse the return shipping cost and cover freight on the correct part. Contact [email protected] with the order number to start either process.
Cross-reference & fitment
Cross-reference on the 10118 hinge pin is straightforward: match the OEM part number from the lift's parts breakdown against the number on your original invoice. If the numbers match, the component fits. If your lift's parts breakdown lists a superseded or alternate number, we accept the superseded value on the phone as confirmation of fit. When a manufacturer has issued a running change during production, we track the change in our catalog so ordering by the older number automatically pulls the current-spec replacement.
Questions about the 10118 hinge pin? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
Hinge Pin Lock Ring - Nussbaum - 10.118
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.