The Rotary FJ7276-1 replacement hardware is the direct replacement for the Rotary lift it came off of. Cross-referenced as ALS-7507-95, it is the genuine Rotary part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Rotary replacement hardware from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-7507-95
- Brand: Rotary
- Type: Genuine OEM replacement hardware
Nobody budgets for a washer. That is exactly how a bay ends up dead for three days — the big components get stocked and scheduled, and then the lift goes down over a pin, a clip, or a spring that nobody thought to have on the shelf. Hardware is the highest-leverage inventory in lift maintenance: the unit cost is trivial, the failure mode is a stopped bay, and the lead time is the same freight wait as any other part. When you order the hardware that failed, order its twin on the other side of the lift too — both sides carry the same hours, so the second failure is already scheduled whether you planned for it or not.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
- Clevis Pin - Rotary FA2230-12
- Bracket - Rotary FA2230-17
- Slotted Bracket Assembly - Rotary - FA2230-97 FA2230-97BK
- Bracket Weldment - Rotary - FJ7253-1
- RH Yoke Bracket - Rotary - FJ7233-19BK
- Right Hand Retrofit Bracket - Rotary - FJ7276-2
Check your lift's serial before ordering
The most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so "it fits my lift model" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift.
Can't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week.
Check the mirror position of whatever failed. Lifts are symmetric machines: the same pin, spring, or bushing exists on the other column or the other end of the crossbeam, with identical hours on it. If one side measured worn, the other side is close behind, and the labor is already paid while the lift is apart. Also inspect the hardware you had to remove for access — disturbed fasteners deserve a look before reuse.
Waiting on a hardware part is not a reason to run the lift without it. A lift missing a retaining clip or running a known-broken spring is out of service until the part arrives — the couple of days of patience is cheaper than what an unretained pin lets go of.
Why buy your Rotary replacement hardware from Auto Lift Services
We install, inspect, and repair Rotary lifts every week — the ALS-7507-95 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine Rotary — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this fj7276 hand retrofit
The fj7276 hand retrofit is a direct-fit replacement engineered to restore original manufacturer performance on the lift model it services. Every piece we ship carries the exact dimensional and material specifications the OEM published for that application. Fitment on this component is critical: it interfaces with adjacent hardware in ways that any deviation from spec can drive premature wear on nearby parts or trigger the lift's mechanical safety systems into an unexpected condition. Shops that source this from us instead of a generic aftermarket substitute consistently report zero fitment issues on first-time installation.
Technical specification & installation notes
Torque and installation notes for this component follow the manufacturer's service manual. Where a torque value is called out, use a calibrated torque wrench and follow the tightening sequence the manual publishes for that fastener location — many lift assemblies require star-pattern or crosswise tightening to distribute load evenly. Skipping that step is one of the most common reasons a correctly-sourced fj7276 hand retrofit still ends up needing to be re-serviced within a year. Our tech line at 800-674-9302 will walk your installer through the procedure if the shop does not have the current service manual on hand.
Shipping & ordering
Placing an order online is the fastest path — add to cart, check out, done. If the shop needs a purchase order, net-30 terms, or a formal quote for a fleet-service contract, our accounts team handles those via email at [email protected] or by phone at 800-674-9302. Volume pricing on the fj7276 hand retrofit kicks in at 10+ pieces on the same order for common wear items. Ask about the volume rate specifically before you check out — many fleet buyers stock 6-12 pieces at a time and the discount is meaningful over that shelf life.
Warranty coverage
Every fj7276 hand retrofit sold through Automotive Lift Services carries a one-year manufacturer-defect warranty. If it fails within that window due to a defect in material or workmanship, we replace it at no charge. Damage from improper installation, use outside the lift's rated capacity, side-loading, or modifications to the parent lift are not covered. The warranty is documented on your original order receipt — retain that record for the coverage period. To submit a warranty claim, contact us with the order number and a photo of the failure at [email protected].
Cross-reference & fitment
Fitment on the fj7276 hand retrofit is verified against the lift serial number when the order comes in. Even inside one manufacturer's catalog, a lift model built in one production year can carry subtle revisions from the same model built two or three years later. Sending us the lift serial number when you place the order — either in the order notes or in a follow-up email — lets us verify the piece against that specific serial's parts list. That five-minute step catches revision mismatches before shipping and prevents the delay of an incorrect delivery.
Questions about the fj7276 hand retrofit? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
Left Hand Retrofit Bracket - Rotary - FJ7276-1
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.