LENZ ODC-12 Outside Deburring Cutter 3/4" — a direct-fit replacement replacement part. Ordering the replacement part from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: BL-5004-09
- Type: Genuine OEM replacement part
Do the math on a dead lift bay: a bay that bills steadily is producing hundreds of dollars a day, and the part holding it hostage is very often something small. That is the real cost equation on lift parts — not the price on this page, but the days between failure and repair. The shops that feel it worst are the ones that wait until a part strands a vehicle in the air on a Friday. Keeping the known wear items on hand, or ordering them the day symptoms show up, keeps a twenty-dollar part from charging you a week’s rent on the bay it shut down.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
- LENZ ODC-10 Outside Deburring Cutter 5/8"
- Steel Hyd-Line Tubing (20')
- Steel Hyd-Line Tubing (10')
- Steel Hyd-Line Tubing (20')
- Steel Hyd-Line Tubing (20')
- Steel Hyd-Line Tubing (20')
Not sure this fits? Here's how to check
Pull the number off your lift's model plate first — model and serial both. Manufacturers run mid-cycle revisions that keep the model name but change hardware, so two lifts with the same name on the column can take different parts. The serial is what removes the guesswork.
Second check: compare the old part against this listing before you order. Length, mounting pattern, and thread sizes tell most of the story. If anything doesn't line up, or if the old part is too worn or broken to measure, call us with photos — we work on these lifts every week and can usually confirm fit from a picture and the lift's serial faster than you can dig through a parts diagram.
While the lift is already apart, replace what is on the same clock. Parts that wear together should be replaced together — the labor of opening the lift up is the expensive half of the job, and doing it twice for two parts that could have shipped in one box is the most common money leak in lift maintenance. Check the mating parts, the hardware, and anything you had to disturb to get here.
Downtime pressure is exactly when shortcuts happen — the temporary fix, the not-quite-right part, the lock that gets bypassed for one job. Do not let a busy schedule talk you into running a lift in a condition you would flag on someone else’s equipment.
Why buy your replacement part from Auto Lift Services
We install, inspect, and repair automotive lifts every week — the BL-5004-09 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine OEM — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this odc 12 lenz outside
Every order for the odc 12 lenz outside starts with a fitment confirmation. Two lifts of the same model can carry subtle revisions between production years, and a component that fits a rev-A lift may not fit a rev-B lift built two years later. Before your card is charged we verify the piece against the parts breakdown for your specific lift serial number. That five-minute step is the difference between the part arriving and being installed the same afternoon versus the wrong piece showing up and the shop losing a day of billable work.
Technical specification & installation notes
Torque and installation notes for this component follow the manufacturer's service manual. Where a torque value is called out, use a calibrated torque wrench and follow the tightening sequence the manual publishes for that fastener location — many lift assemblies require star-pattern or crosswise tightening to distribute load evenly. Skipping that step is one of the most common reasons a correctly-sourced odc 12 lenz outside still ends up needing to be re-serviced within a year. Our tech line at 800-674-9302 will walk your installer through the procedure if the shop does not have the current service manual on hand.
Shipping & ordering
Shipping runs 3-5 business days on standard ground to the lower 48 states. Expedited overnight and two-day options are available; call 800-674-9302 before ordering to quote expedited freight. We stock the odc 12 lenz outside in Iowa and ship same-day for orders confirmed before 2 PM Central. Orders that come in later than that or on a Friday afternoon pick up on the next business day. A tracking number gets emailed to the address on the order the moment the package leaves our dock.
Warranty coverage
Consumables and wear parts like this are covered under the manufacturer defect warranty for twelve months. Because the odc 12 lenz outside is a component that eventually needs replacement in normal operation, warranty coverage specifically addresses failure due to manufacturing defect, not failure due to normal end-of-life wear. Our team can help distinguish between the two on a phone call if there is any question after installation — call 800-674-9302 and describe the failure pattern; we will tell you honestly whether it looks like a warranty case.
Cross-reference & fitment
Cross-reference on the odc 12 lenz outside is straightforward: match the OEM part number from the lift's parts breakdown against the number on your original invoice. If the numbers match, the component fits. If your lift's parts breakdown lists a superseded or alternate number, we accept the superseded value on the phone as confirmation of fit. When a manufacturer has issued a running change during production, we track the change in our catalog so ordering by the older number automatically pulls the current-spec replacement.
Questions about the odc 12 lenz outside? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
LENZ ODC-12 Outside Deburring Cutter 3/4"
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.