The Rotary N2101-1 lift arm component is the direct replacement for the Rotary lift it came off of. Cross-referenced as ALS-7545-36, it is the genuine Rotary part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Rotary lift arm component from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-7545-36
- Brand: Rotary
- Type: Genuine OEM lift arm component
- Fits: SPOA7
- Lift type: 2-post lift
The restraint gear on a 2-post lift is the toothed gear that engages when the lifting arm swings in under load, locking the arm at whatever angle the tech set it to. When teeth wear round, chip, or the pawl gear that engages into the restraint gear loses its point, the arm can swing under load — and a swung arm with a vehicle on it drops the vehicle. Any restraint gear that will not positively catch the arm under light hand pressure needs to come off, whether the teeth look okay or not.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
- Arm Restraint Engage Gear - Rotary N2121
- Outer Rear Swing Arm - Rotary N2150-1
- Inner Rear Swing Arm Kit - Rotary N2103-1
- Arm Swivel Pin - Rotary N2154
- Arm Restraint Gear (Adjustable) - Rotary SVI Exclusive
- Arm Restraint Gear (Not Adjustable) - Rotary N2122
Ordering the right revision
Before this goes in the cart, grab two things off your lift: the model number and the serial number, both on the manufacturer's plate. The serial matters more than most people expect — lift makers revise components between production runs without renaming the lift, and the run your serial falls in determines which revision of this part is correct.
If you are working from a failed part rather than a plate, measure what you have and photograph how it mounts. Send that to us along with the lift brand, and we will check it against the same parts breakdowns our own techs use in the field before you commit to the order.
Also inspect
- Arm pin — if you had a bad restraint gear you may also have a mushroomed or grooved arm pin
- Foot-pad rubber — intact, securely attached
- Return spring on the pawl
- Arm itself — broken welds, cracks, severe rust
A restraint gear that will not engage is a lift that is unsafe to load. Do not put a vehicle on the lift until you confirm both arms lock positively under hand pressure.
Why buy your Rotary lift arm component from Auto Lift Services
We install, inspect, and repair Rotary lifts every week — the ALS-7545-36 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine Rotary — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this n2101 inner rear
Sourcing the correct n2101 inner rear is not the spot a shop wants to gamble. This piece sits inside a load path the lift manufacturer engineered to specific tolerances, and a substitute that looks close but is off by even a small margin can transfer load onto a neighboring component that was not designed for it. We stock this exact part to the OEM specification the original manufacturer publishes, which is why techs who have been through a bad aftermarket cycle keep coming back to us for the same replacement whenever their next need comes up.
Technical specification & installation notes
Cycle life on this piece depends heavily on operating conditions. In a typical commercial repair shop running 6-10 lifts per day, the n2101 inner rear should deliver five to eight years of service before showing measurable wear against the OEM inspection specification. In a high-volume tire or alignment shop running 20+ lifts per day per bay, expect service every three to five years. It is designed to be a serviceable component; when it does wear it wears within safe operating margins that trigger visible symptoms — drift, uneven wear, minor leakage — well before failure becomes a safety issue.
Shipping & ordering
Freight covers the continental United States on all standard orders. We ship UPS or FedEx ground for parts under 30 lb; heavier assemblies quote at published carrier rates. International orders on the n2101 inner rear require a freight quote — email dimensions, weight, and destination country to [email protected] and we return a rate within one business day. Alaska, Hawaii, and US territories quote at published rates and typically take five to ten business days depending on carrier and destination.
Warranty coverage
Return policy on the n2101 inner rear follows our store-wide standard: all parts sales are final; exchanges only if the piece arrives defective. In the case of a defective delivery, ship the failed piece back to us at your cost, we verify the defect on receipt, and ship a replacement at ours. Wrong-item deliveries where we made the shipping error follow a different path — we reimburse the return shipping cost and cover freight on the correct part. Contact [email protected] with the order number to start either process.
Cross-reference & fitment
Cross-reference on the n2101 inner rear is straightforward: match the OEM part number from the lift's parts breakdown against the number on your original invoice. If the numbers match, the component fits. If your lift's parts breakdown lists a superseded or alternate number, we accept the superseded value on the phone as confirmation of fit. When a manufacturer has issued a running change during production, we track the change in our catalog so ordering by the older number automatically pulls the current-spec replacement.
Questions about the n2101 inner rear? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
Inner Rear Swing Arm Kit (newer) - Rotary N2101-1
Parts that fit your lift
This Rotary part fits the lift models below. Click your model to see every part that fits it — handy for grabbing the wear items that usually go at the same time (cables, sheaves, pins, locks).
Browse all Rotary lift parts →Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.