The Rotary N414 electrical control component is the direct replacement for the Rotary lift it came off of. Cross-referenced as ALS-7538-55, it is the genuine Rotary part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Rotary electrical control component from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-7538-55
- Brand: Rotary
- Type: Genuine OEM electrical control component
- Fits: SPO12 EH-1, SPO12 EH-2, SPO15, SPO15 300 Series, SPO18, SPO18 300 Series
- Lift type: 2-post lift
Electrical wear is about cycles and connections. Every press of the up button makes and breaks a contactor's points, and those points erode a little each time until they no longer pass full current. Loose connections aren't age so much as vibration and heat working a lug loose over the years. A motor's bearings and start capacitor are the parts that clock hours; the switchgear wears by count of starts.
A lift motor tells you it's failing before it quits. It hums but won't turn (a dead start capacitor or a seized pump), it starts slow or weak (worn windings or low voltage), it trips the overload after a minute (drawing too much current), or it runs hot and smells of scorched varnish (insulation breaking down). A motor that's tripping, humming, or smelling hot is on its way out.
What lifts this electrical control component fits
This electrical control component fits the lift models below. Click a model to open its visual parts breakdown — the exploded drawing with every part numbered, so you can confirm this is the right part for your exact lift before you order.
- SPO12 — see the exploded parts breakdown for this lift
- SPO15 — see the exploded parts breakdown for this lift
- SPO18 — see the exploded parts breakdown for this lift
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
- Overhead Limit Switch (under 250V) - Rotary N413-1
- Microswitch - Rotary - P461-2
- Toggle Switch - Rotary - P423-2
- Micro Switch - Rotary - P441-2
Replacing your electrical control component
Most lift electrical work follows the same order: verify power is off, trace the circuit from source to motor, replace the failed part, then power up and test both operation and the safety stops. Guessing at where in the chain the fault lives wastes time and risks the wrong part. For that reason the full procedure is worth reading first. Not sure on the procedure? Find your lift in our parts lookup or call and we will walk you through it.
Find the right part for your lift
If you are not sure this part matches your setup, the fastest check is the visual breakdown: open our Rotary parts lookup, pick your model, and match your part against the drawing where every item is numbered. Can't read the model plate? our guide to finding your model number shows exactly where it lives on each lift type, and we are a phone call away if you would rather have us confirm it.
Signs of an electrical fault
For the motor, check what it does when energized. Humming without turning points to a dead start capacitor or a seized pump; test the cap and try to turn the pump by hand. A motor that trips the overload after running briefly is drawing too much current — worn bearings, bad windings, or a binding pump. Feel for excess heat and listen for bearing growl or grinding.
Parts commonly replaced at the same time
Electrical faults often involve more than one component — a failed contactor can take a relay or a switch with it, and worn wiring shows up alongside. While the panel is open, check the companions so you are not back in there next week. Tell us your lift's voltage and phase and we will match the related parts.
Safety notes
Isolate the lift from power before you touch any electrical component — lock the disconnect out if the shop has one. Lift control circuits mix line voltage with low-voltage safety inputs, and a miswire can defeat an overhead shutoff or a lock. If you are not confident on the control system, stop and call for help before something moves unexpectedly.
Before you order
Have the data plate in front of you — model, serial, voltage, phase — before ordering electrical parts. These details decide which relay, switch, or motor fits, and getting them wrong means a return. If the markings on the old component are readable, share them and we will match exactly.
Not sure this fits? Here's how to check
Pull the number off your lift's model plate first — model and serial both. Manufacturers run mid-cycle revisions that keep the model name but change hardware, so two lifts with the same name on the column can take different parts. The serial is what removes the guesswork.
Second check: compare the old part against this listing before you order. Length, mounting pattern, and thread sizes tell most of the story. If anything doesn't line up, or if the old part is too worn or broken to measure, call us with photos — we work on these lifts every week and can usually confirm fit from a picture and the lift's serial faster than you can dig through a parts diagram.
Why buy your Rotary electrical control component from Auto Lift Services
We install, inspect, and repair Rotary lifts every week — the ALS-7538-55 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302 — and every part ships genuine, no aftermarket substitution unless you ask for it.
About this n414 limit switch
Sourcing the correct n414 limit switch is not the spot a shop wants to gamble. This piece sits inside a load path the lift manufacturer engineered to specific tolerances, and a substitute that looks close but is off by even a small margin can transfer load onto a neighboring component that was not designed for it. We stock this exact part to the OEM specification the original manufacturer publishes, which is why techs who have been through a bad aftermarket cycle keep coming back to us for the same replacement whenever their next need comes up.
Technical specification & installation notes
Torque and installation notes for this component follow the manufacturer's service manual. Where a torque value is called out, use a calibrated torque wrench and follow the tightening sequence the manual publishes for that fastener location — many lift assemblies require star-pattern or crosswise tightening to distribute load evenly. Skipping that step is one of the most common reasons a correctly-sourced n414 limit switch still ends up needing to be re-serviced within a year. Our tech line at 800-674-9302 will walk your installer through the procedure if the shop does not have the current service manual on hand.
Shipping & ordering
Placing an order online is the fastest path — add to cart, check out, done. If the shop needs a purchase order, net-30 terms, or a formal quote for a fleet-service contract, our accounts team handles those via email at [email protected] or by phone at 800-674-9302. Volume pricing on the n414 limit switch kicks in at 10+ pieces on the same order for common wear items. Ask about the volume rate specifically before you check out — many fleet buyers stock 6-12 pieces at a time and the discount is meaningful over that shelf life.
Warranty coverage
Return policy on the n414 limit switch follows our store-wide standard: all parts sales are final; exchanges only if the piece arrives defective. In the case of a defective delivery, ship the failed piece back to us at your cost, we verify the defect on receipt, and ship a replacement at ours. Wrong-item deliveries where we made the shipping error follow a different path — we reimburse the return shipping cost and cover freight on the correct part. Contact [email protected] with the order number to start either process.
Cross-reference & fitment
Fitment on the n414 limit switch is verified against the lift serial number when the order comes in. Even inside one manufacturer's catalog, a lift model built in one production year can carry subtle revisions from the same model built two or three years later. Sending us the lift serial number when you place the order — either in the order notes or in a follow-up email — lets us verify the piece against that specific serial's parts list. That five-minute step catches revision mismatches before shipping and prevents the delay of an incorrect delivery.
Questions about the n414 limit switch? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
OH Limit Switch Assy (over 250V) - Rotary N414
Parts that fit your lift
This Rotary part fits the lift models below. Click your model to see every part that fits it — handy for grabbing the wear items that usually go at the same time (cables, sheaves, pins, locks).
Browse all Rotary lift parts →Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.