The Challenger VS10-40-07 replacement part is the direct replacement for the Challenger lift it came off of. Cross-referenced as ALS-7234-116, it is the genuine Challenger part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Challenger replacement part from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-7234-116
- Brand: Challenger
- Type: Genuine OEM replacement part
Lift manufacturers revise their machines mid-production without changing the model name, which means two lifts that look identical across the shop can take different parts. The part number on this page fits a specific design — and the way to be sure it fits yours is the model and serial number on your lift’s data tag, not the model name alone and not memory. Serial-range splits are the most common reason a correctly named part comes back: right lift, wrong revision. Thirty seconds with the data tag before you order beats a week of freight in both directions.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
- Wire Tie for Mech lock 39000 - Challenger - 31118
- 8" Zip Tie (Long) for DPC Pendant Cords - Challenger - 40346
- Retainer Ring - Challenger - VS10-35-06
- Retaining Wire - Challenger - VS10-35-08
- Overhead Channel $ 1,459.74 $ 1,313.76 - Challenger - 12039 CL12039
- Overhead Shutoff Bar only - Challenger - 12075
Not sure this fits? Here's how to check
Pull the number off your lift's model plate first — model and serial both. Manufacturers run mid-cycle revisions that keep the model name but change hardware, so two lifts with the same name on the column can take different parts. The serial is what removes the guesswork.
Second check: compare the old part against this listing before you order. Length, mounting pattern, and thread sizes tell most of the story. If anything doesn't line up, or if the old part is too worn or broken to measure, call us with photos — we work on these lifts every week and can usually confirm fit from a picture and the lift's serial faster than you can dig through a parts diagram.
Find the data tag — usually on a column or the power unit — and read the model and serial before ordering. If the tag is painted over, gone, or unreadable, look for numbers stamped into the old part itself, or send us a photo of the part and its mounting; we identify lift parts from photos every week. While you are at the tag, note it somewhere permanent, because you will need it again.
If the replacement does not match the old part when you unbox it, stop and call before installing it. Forcing a near-fit part onto a lift is how a parts order turns into a structural problem — the fit difference usually exists for a reason.
Why buy your Challenger replacement part from Auto Lift Services
We install, inspect, and repair Challenger lifts every week — the ALS-7234-116 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine Challenger — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this vs10 overhead shutoff
Every order for the vs10 overhead shutoff starts with a fitment confirmation. Two lifts of the same model can carry subtle revisions between production years, and a component that fits a rev-A lift may not fit a rev-B lift built two years later. Before your card is charged we verify the piece against the parts breakdown for your specific lift serial number. That five-minute step is the difference between the part arriving and being installed the same afternoon versus the wrong piece showing up and the shop losing a day of billable work.
Technical specification & installation notes
Cycle life on this piece depends heavily on operating conditions. In a typical commercial repair shop running 6-10 lifts per day, the vs10 overhead shutoff should deliver five to eight years of service before showing measurable wear against the OEM inspection specification. In a high-volume tire or alignment shop running 20+ lifts per day per bay, expect service every three to five years. It is designed to be a serviceable component; when it does wear it wears within safe operating margins that trigger visible symptoms — drift, uneven wear, minor leakage — well before failure becomes a safety issue.
Shipping & ordering
Freight covers the continental United States on all standard orders. We ship UPS or FedEx ground for parts under 30 lb; heavier assemblies quote at published carrier rates. International orders on the vs10 overhead shutoff require a freight quote — email dimensions, weight, and destination country to [email protected] and we return a rate within one business day. Alaska, Hawaii, and US territories quote at published rates and typically take five to ten business days depending on carrier and destination.
Warranty coverage
Return policy on the vs10 overhead shutoff follows our store-wide standard: all parts sales are final; exchanges only if the piece arrives defective. In the case of a defective delivery, ship the failed piece back to us at your cost, we verify the defect on receipt, and ship a replacement at ours. Wrong-item deliveries where we made the shipping error follow a different path — we reimburse the return shipping cost and cover freight on the correct part. Contact [email protected] with the order number to start either process.
Cross-reference & fitment
Cross-reference on the vs10 overhead shutoff is straightforward: match the OEM part number from the lift's parts breakdown against the number on your original invoice. If the numbers match, the component fits. If your lift's parts breakdown lists a superseded or alternate number, we accept the superseded value on the phone as confirmation of fit. When a manufacturer has issued a running change during production, we track the change in our catalog so ordering by the older number automatically pulls the current-spec replacement.
Questions about the vs10 overhead shutoff? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
Overhead Shutoff Bar - Challenger - VS10-40-07
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.