The Forward 106801BL replacement hardware is the direct replacement for the Forward lift it came off of. Cross-referenced as ALS-7239-100, it is the genuine Forward part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Forward replacement hardware from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-7239-100
- Brand: Forward
- Type: Genuine OEM replacement hardware
Nobody budgets for a washer. That is exactly how a bay ends up dead for three days — the big components get stocked and scheduled, and then the lift goes down over a pin, a clip, or a spring that nobody thought to have on the shelf. Hardware is the highest-leverage inventory in lift maintenance: the unit cost is trivial, the failure mode is a stopped bay, and the lead time is the same freight wait as any other part. When you order the hardware that failed, order its twin on the other side of the lift too — both sides carry the same hours, so the second failure is already scheduled whether you planned for it or not.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
- Bearing CR14, RFP14 - Forward - H4P-3001
- Spring CR14, RFP14 - Forward - H4P-1015
- Roller Pin - Forward - FC5991Y
- Pin - Forward - H4P-1017FWD
- 3/8 JIC Swivel Nut 45 Deg #6502-6 - Forward - 992464
- Shaft Weldment - Forward - 250405
Not sure this fits? Here's how to check
Pull the number off your lift's model plate first — model and serial both. Manufacturers run mid-cycle revisions that keep the model name but change hardware, so two lifts with the same name on the column can take different parts. The serial is what removes the guesswork.
Second check: compare the old part against this listing before you order. Length, mounting pattern, and thread sizes tell most of the story. If anything doesn't line up, or if the old part is too worn or broken to measure, call us with photos — we work on these lifts every week and can usually confirm fit from a picture and the lift's serial faster than you can dig through a parts diagram.
Check the mirror position of whatever failed. Lifts are symmetric machines: the same pin, spring, or bushing exists on the other column or the other end of the crossbeam, with identical hours on it. If one side measured worn, the other side is close behind, and the labor is already paid while the lift is apart. Also inspect the hardware you had to remove for access — disturbed fasteners deserve a look before reuse.
Waiting on a hardware part is not a reason to run the lift without it. A lift missing a retaining clip or running a known-broken spring is out of service until the part arrives — the couple of days of patience is cheaper than what an unretained pin lets go of.
Why buy your Forward replacement hardware from Auto Lift Services
We install, inspect, and repair Forward lifts every week — the ALS-7239-100 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine Forward — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this dp97 overhead weldment
Every order for the dp97 overhead weldment starts with a fitment confirmation. Two lifts of the same model can carry subtle revisions between production years, and a component that fits a rev-A lift may not fit a rev-B lift built two years later. Before your card is charged we verify the piece against the parts breakdown for your specific lift serial number. That five-minute step is the difference between the part arriving and being installed the same afternoon versus the wrong piece showing up and the shop losing a day of billable work.
Technical specification & installation notes
Technical specification matches the OEM published dimensions to within manufacturing tolerance. When a shop installs the dp97 overhead weldment correctly, the lift returns to factory-rated performance immediately — no break-in period, no cycle-count adjustment required. The lift's safety systems (mechanical locks, hydraulic pressure relief, and electrical interlocks) treat a correctly-installed replacement exactly as they would treat a factory-original component during initial commissioning. That parity is what lets us honor warranty coverage without asking for the lift's full operating history.
Shipping & ordering
Freight covers the continental United States on all standard orders. We ship UPS or FedEx ground for parts under 30 lb; heavier assemblies quote at published carrier rates. International orders on the dp97 overhead weldment require a freight quote — email dimensions, weight, and destination country to [email protected] and we return a rate within one business day. Alaska, Hawaii, and US territories quote at published rates and typically take five to ten business days depending on carrier and destination.
Warranty coverage
Return policy on the dp97 overhead weldment follows our store-wide standard: all parts sales are final; exchanges only if the piece arrives defective. In the case of a defective delivery, ship the failed piece back to us at your cost, we verify the defect on receipt, and ship a replacement at ours. Wrong-item deliveries where we made the shipping error follow a different path — we reimburse the return shipping cost and cover freight on the correct part. Contact [email protected] with the order number to start either process.
Cross-reference & fitment
Fitment on the dp97 overhead weldment is verified against the lift serial number when the order comes in. Even inside one manufacturer's catalog, a lift model built in one production year can carry subtle revisions from the same model built two or three years later. Sending us the lift serial number when you place the order — either in the order notes or in a follow-up email — lets us verify the piece against that specific serial's parts list. That five-minute step catches revision mismatches before shipping and prevents the delay of an incorrect delivery.
Questions about the dp97 overhead weldment? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
Overhead Weldment DP97, DP10 - Forward - 106801BL 106801
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.