The Weaver ALS-9670-44 is the direct-replacement replacement part for the Weaver lift it came off of — the genuine part, same fit and same working specification as the one already on your lift. Ordering the Weaver replacement part from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-9670-44
- Brand: Weaver
- Type: Genuine OEM replacement part
This is a manufacturer-spec replacement part for the lift it was designed for — same dimensions, same material, same fit as the part that came off. That matters more on a lift than on most equipment, because lift parts do not work in isolation: a part that is close-but-not-quite transfers its error into whatever it bolts to, rides on, or seals against. A knock-off that is a few thousandths off might install fine and then wear its neighbors for the next five years. When you order to the published spec, the part drops in and the rest of the lift never knows anything changed.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
- Spotting Device - Weaver - AS-16624
- Cover Door for EC-202 - Weaver - AS-23702
- Rear Saddle-long EC102 $ 1,300.17 $ 1,170.16 - Weaver - AS-25550
- Wiper Retainer for 7-1/2" - Weaver - S-5826
- Front Cover Plate 40" - Weaver - AS-28017
- Front Sliding Plate 40" - Weaver - AS-28018
Confirm this is the right part before you order
Lift manufacturers revise parts mid-production without changing the model name, so the same lift bought two years apart can take two different revisions of the same component. Before you order, find the model plate on the lift — on most 2-post lifts it rides on one of the columns at eye level, on 4-post lifts it is usually on a column or the power-unit side runway — and note the full model number and serial. The serial dates the lift to a production run, and that is what decides which revision fits.
If the plate is painted over or missing, take a photo of the part you are replacing next to a tape measure and send it to us. Between the dimensions, the mounting pattern, and what lift it came off of, we can almost always identify the exact part before you spend money on the wrong one.
Before you install the replacement, compare it side by side with the part you removed — length, bore, thread, and mounting pattern should match exactly, not approximately. If the old part is worn out of shape, measure against the mounting points on the lift instead. A mismatch caught on the bench costs you a phone call; a mismatch caught after installation costs you the job twice.
Never modify a lift part to make it fit — no drilling out holes, no grinding down shoulders, no washers-as-spacers improvisation. A part that needs persuasion is the wrong part, and a modified part on a machine that holds vehicles over people is a liability with your name on it.
Why buy your Weaver replacement part from Auto Lift Services
We install, inspect, and repair Weaver lifts every week — the ALS-9670-44 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine Weaver — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this 28020 rear sliding
Every order for the 28020 rear sliding starts with a fitment confirmation. Two lifts of the same model can carry subtle revisions between production years, and a component that fits a rev-A lift may not fit a rev-B lift built two years later. Before your card is charged we verify the piece against the parts breakdown for your specific lift serial number. That five-minute step is the difference between the part arriving and being installed the same afternoon versus the wrong piece showing up and the shop losing a day of billable work.
Technical specification & installation notes
Cycle life on this piece depends heavily on operating conditions. In a typical commercial repair shop running 6-10 lifts per day, the 28020 rear sliding should deliver five to eight years of service before showing measurable wear against the OEM inspection specification. In a high-volume tire or alignment shop running 20+ lifts per day per bay, expect service every three to five years. It is designed to be a serviceable component; when it does wear it wears within safe operating margins that trigger visible symptoms — drift, uneven wear, minor leakage — well before failure becomes a safety issue.
Shipping & ordering
Placing an order online is the fastest path — add to cart, check out, done. If the shop needs a purchase order, net-30 terms, or a formal quote for a fleet-service contract, our accounts team handles those via email at [email protected] or by phone at 800-674-9302. Volume pricing on the 28020 rear sliding kicks in at 10+ pieces on the same order for common wear items. Ask about the volume rate specifically before you check out — many fleet buyers stock 6-12 pieces at a time and the discount is meaningful over that shelf life.
Warranty coverage
Consumables and wear parts like this are covered under the manufacturer defect warranty for twelve months. Because the 28020 rear sliding is a component that eventually needs replacement in normal operation, warranty coverage specifically addresses failure due to manufacturing defect, not failure due to normal end-of-life wear. Our team can help distinguish between the two on a phone call if there is any question after installation — call 800-674-9302 and describe the failure pattern; we will tell you honestly whether it looks like a warranty case.
Cross-reference & fitment
Alternate applications for the 28020 rear sliding sometimes exist. Where a common part fits multiple lift models across a manufacturer's catalog, cross-reference sheets show the compatible models explicitly. If you are consolidating parts stock and want to know which of your lifts the piece covers, email the request to [email protected] with a list of the lift models in your bay — we return a compatibility grid showing which lifts accept the replacement and which need a different number.
Questions about the 28020 rear sliding? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
Rear Sliding Plate 24" - Weaver - AS-28020
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.