The Rotary T120166 replacement hardware is the direct replacement for the Rotary lift it came off of. Cross-referenced as ALS-7521-08, it is the genuine Rotary part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Rotary replacement hardware from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-7521-08
- Brand: Rotary
- Type: Genuine OEM replacement hardware
- Fits: SL210, SL212
- Lift type: inground lift
Hardware is the easiest category to order wrong, because so much of it looks generic — a pin is a pin until it is an eighth of an inch short and the e-clip groove lands inside the bore. Lift makers change hardware dimensions between production runs without renaming the lift, so the part that fits a given model can split by serial range. Order from your lift’s data tag — model and serial — rather than from the model name or from a lookalike photo. If the tag is gone, the old hardware itself is the spec: measure it, or photograph it next to a tape measure and send it to us, and we will match it before it ships.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
- 1/2-13NC x 1-1/4" Countersunk Socket Head Cap Screw - Rotary 40337
- Stop Bolt - Rotary - 41650
- Nut - Rotary - 40672
- Pivot Pin $ 1,433.84 $ 1,290.45 - Rotary - AP01339
- Cotter Pin - Rotary - 41200
Check your lift's serial before ordering
The most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so "it fits my lift model" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift.
Can't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week.
Measure the old part before you order and again against the new part when it arrives: overall length, diameter, groove and cross-hole locations, and thread size on anything threaded. On threaded hardware, run the nut on by hand first — if it fights, check for welding slag or damaged threads and clean them up with a file rather than powering the nut on and wrecking both parts.
Close is not correct on load-bearing hardware. A pin that is slightly undersized hammers its bore oval; a bolt of the wrong grade shears under a load the right one shrugs off. If what arrived does not match what came out, install nothing and call — guessing is the one move with no good outcome.
Why buy your Rotary replacement hardware from Auto Lift Services
We install, inspect, and repair Rotary lifts every week — the ALS-7521-08 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine Rotary — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this t120166 lift bar
The t120166 lift bar is a direct-fit replacement engineered to restore original manufacturer performance on the lift model it services. Every piece we ship carries the exact dimensional and material specifications the OEM published for that application. Fitment on this component is critical: it interfaces with adjacent hardware in ways that any deviation from spec can drive premature wear on nearby parts or trigger the lift's mechanical safety systems into an unexpected condition. Shops that source this from us instead of a generic aftermarket substitute consistently report zero fitment issues on first-time installation.
Technical specification & installation notes
Technical specification matches the OEM published dimensions to within manufacturing tolerance. When a shop installs the t120166 lift bar correctly, the lift returns to factory-rated performance immediately — no break-in period, no cycle-count adjustment required. The lift's safety systems (mechanical locks, hydraulic pressure relief, and electrical interlocks) treat a correctly-installed replacement exactly as they would treat a factory-original component during initial commissioning. That parity is what lets us honor warranty coverage without asking for the lift's full operating history.
Shipping & ordering
Placing an order online is the fastest path — add to cart, check out, done. If the shop needs a purchase order, net-30 terms, or a formal quote for a fleet-service contract, our accounts team handles those via email at [email protected] or by phone at 800-674-9302. Volume pricing on the t120166 lift bar kicks in at 10+ pieces on the same order for common wear items. Ask about the volume rate specifically before you check out — many fleet buyers stock 6-12 pieces at a time and the discount is meaningful over that shelf life.
Warranty coverage
Return policy on the t120166 lift bar follows our store-wide standard: all parts sales are final; exchanges only if the piece arrives defective. In the case of a defective delivery, ship the failed piece back to us at your cost, we verify the defect on receipt, and ship a replacement at ours. Wrong-item deliveries where we made the shipping error follow a different path — we reimburse the return shipping cost and cover freight on the correct part. Contact [email protected] with the order number to start either process.
Cross-reference & fitment
Fitment on the t120166 lift bar is verified against the lift serial number when the order comes in. Even inside one manufacturer's catalog, a lift model built in one production year can carry subtle revisions from the same model built two or three years later. Sending us the lift serial number when you place the order — either in the order notes or in a follow-up email — lets us verify the piece against that specific serial's parts list. That five-minute step catches revision mismatches before shipping and prevents the delay of an incorrect delivery.
Questions about the t120166 lift bar? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
Lift Bar Weldment - Rotary T120166
Parts that fit your lift
This Rotary part fits the lift models below. Click your model to see every part that fits it — handy for grabbing the wear items that usually go at the same time (cables, sheaves, pins, locks).
Browse all Rotary lift parts →Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.