The Tuxedo TP11KC-DX-061 replacement hardware is the direct replacement for the Tuxedo lift it came off of. Cross-referenced as ALS-7485-0539, it is the genuine Tuxedo part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Tuxedo replacement hardware from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-7485-0539
- Brand: Tuxedo
- Type: Genuine OEM replacement hardware
On lift hardware, fit is the whole job. A pin is not a rod of roughly the right diameter — it is a specific length, a specific fit in its bore, and a specific way of being retained, whether that is an e-clip groove, a cotter key hole, or a shoulder. A bushing is a precise interference in its housing and a precise clearance on its shaft. Manufacturer-spec hardware carries all of those dimensions; the hardware-aisle stand-in carries some of them, and the missing ones become play, wobble, and premature wear. This is a spec-correct replacement for the assembly it belongs to — it goes in the way the original came out, retained the way the original was retained.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
- Tuxedo TP9-1004 Spindle Spring Washer
- Tuxedo TP9-1038.1 Nesting Height Extension - 3" w/1-3/8" pin
- Tuxedo TP9-1038 Nesting Height Extension - 1-1/2" w/1-3/8" pin
- Tuxedo TP9-1039 Nesting Height Extension - 5" w/1-3/8" pin
- Tuxedo TP9-1065 Elevator Bolt
- Tuxedo TP9KACX-032 QYS-200-17 Spring
Check your lift's serial before ordering
The most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so "it fits my lift model" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift.
Can't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week.
Lay the new piece against the old before installing: length, diameter, groove and hole positions, thread pitch. If the old part is too worn to compare against, check the new part in its bore or against its mate by hand — it should fit the way a machined part fits, snug and smooth, not loose and not forced. Replace the retaining clips and keys while you are there; they are one-use money.
Retention is not optional. A pin without its e-clip, cotter key, or bolt is a pin working its way out under vibration, and what it drops depends on where it lives. If the retainer came off damaged, replace it — never spring a used clip back on and call it held.
Why buy your Tuxedo replacement hardware from Auto Lift Services
We install, inspect, and repair Tuxedo lifts every week — the ALS-7485-0539 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine Tuxedo — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this tp11kc tuxedo kac
Every order for the tp11kc tuxedo kac starts with a fitment confirmation. Two lifts of the same model can carry subtle revisions between production years, and a component that fits a rev-A lift may not fit a rev-B lift built two years later. Before your card is charged we verify the piece against the parts breakdown for your specific lift serial number. That five-minute step is the difference between the part arriving and being installed the same afternoon versus the wrong piece showing up and the shop losing a day of billable work.
Technical specification & installation notes
Technical specification matches the OEM published dimensions to within manufacturing tolerance. When a shop installs the tp11kc tuxedo kac correctly, the lift returns to factory-rated performance immediately — no break-in period, no cycle-count adjustment required. The lift's safety systems (mechanical locks, hydraulic pressure relief, and electrical interlocks) treat a correctly-installed replacement exactly as they would treat a factory-original component during initial commissioning. That parity is what lets us honor warranty coverage without asking for the lift's full operating history.
Shipping & ordering
Freight covers the continental United States on all standard orders. We ship UPS or FedEx ground for parts under 30 lb; heavier assemblies quote at published carrier rates. International orders on the tp11kc tuxedo kac require a freight quote — email dimensions, weight, and destination country to [email protected] and we return a rate within one business day. Alaska, Hawaii, and US territories quote at published rates and typically take five to ten business days depending on carrier and destination.
Warranty coverage
Consumables and wear parts like this are covered under the manufacturer defect warranty for twelve months. Because the tp11kc tuxedo kac is a component that eventually needs replacement in normal operation, warranty coverage specifically addresses failure due to manufacturing defect, not failure due to normal end-of-life wear. Our team can help distinguish between the two on a phone call if there is any question after installation — call 800-674-9302 and describe the failure pattern; we will tell you honestly whether it looks like a warranty case.
Cross-reference & fitment
Alternate applications for the tp11kc tuxedo kac sometimes exist. Where a common part fits multiple lift models across a manufacturer's catalog, cross-reference sheets show the compatible models explicitly. If you are consolidating parts stock and want to know which of your lifts the piece covers, email the request to [email protected] with a list of the lift models in your bay — we return a compatibility grid showing which lifts accept the replacement and which need a different number.
Questions about the tp11kc tuxedo kac? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
Tuxedo TP11KC-DX-061 TP11KAC-D3-08 Main Side Bracket
Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.