The Challenger 6-3032 safety decal set is the direct replacement for the Challenger lift it came off of. This is the genuine Challenger part — same fit and same working specification as the one already on your lift. Ordering the Challenger safety decal set from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.

Specifications

• Part number: 6-3032
• Brand: Challenger
• Type: Genuine OEM safety decal set
• Fits: 4018XFX

Skipping the paperwork parts has real consequences. A lift without legible capacity and safety decals is out of compliance and leaves an operator guessing at the load limit; a lift worked on without the manual gets specs and torque values guessed instead of looked up. These aren't cosmetic. The decal and the manual are how the next person — an operator, an inspector, a tech — knows what the lift can do and how to service it right.

What lifts this safety decal set fits

This safety decal set fits the lift models below. Click a model to open its visual parts breakdown — the exploded drawing with every part numbered, so you can confirm this is the right part for your exact lift before you order.

• 4018XFX — see the exploded parts breakdown for this lift

Related parts for this lift

The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.

• Challenger 6-1637 Decal 4-Post Safety Locks
• Challenger 6-1764 12K Capacity Decal
• Challenger 6-3031 Decal Up
• Challenger 6-3558 Decal Safety Release
• Challenger 6-3623 Decal Duty Cycle
• Challenger 6-3696 Decal Oil Level Lubricator

Replacing your safety decal set

Sorting out the air supply — compressor, regulator, moisture trap — is about delivering clean, steady pressure to the lock system on demand. Set the regulator, drain the trap, and confirm the pressure holds while the locks cycle. The step-by-step guide lays out the settings and checks. Not sure on the procedure? Find your lift in our parts lookup or call and we will walk you through it.

Find the right part for your lift

Not certain this is the exact part your lift needs? Start with your lift's model and serial off the data plate, then open our Challenger parts lookup to see the visual parts breakdown for your model — the exploded drawing with every part numbered and priced. If your plate is missing or unreadable, our guide to finding your model number walks through where to find it, or send us a photo and we will identify the lift for you.

Signs it's time to replace it

For any replacement part, verify it matches the original before it goes on — size, rating, mounting, and function. Set the new part next to the old one and confirm they're the same where it counts. A support part that's close but not right — a slightly different fitting, a lower-grade bolt, an off-size clip — either won't do its job or won't fit at all. Match it to what came off.

Parts commonly replaced at the same time

Since you are already ordering, tell us your lift and we will point out what else it commonly needs — related hardware, safety labeling, accessories rated for your model. Consolidating into one order is cheaper and simpler than piecing it together over several. We keep the breakdown for your lift on hand.

Safety notes

The little parts round out a safe, compliant lift. Use the correct component for your model, keep the required labeling in place and readable, and follow the manufacturer's install notes. If you are not sure which version your lift takes, a quick call saves a wrong order and a second trip up the ladder.

Before you order

Before ordering, confirm your lift's model and serial so we can match the correct version — even simple parts have revisions. If you are replacing a decal set or an accessory, tell us the model and we will make sure you get the one specified for your lift rather than a near-miss.

Confirm this is the right part before you order

Lift manufacturers revise parts mid-production without changing the model name, so the same lift bought two years apart can take two different revisions of the same component. Before you order, find the model plate on the lift — on most 2-post lifts it rides on one of the columns at eye level, on 4-post lifts it is usually on a column or the power-unit side runway — and note the full model number and serial. The serial dates the lift to a production run, and that is what decides which revision fits.

If the plate is painted over or missing, take a photo of the part you are replacing next to a tape measure and send it to us. Between the dimensions, the mounting pattern, and what lift it came off of, we can almost always identify the exact part before you spend money on the wrong one.

Why buy your Challenger safety decal set from Auto Lift Services

We install, inspect, and repair Challenger lifts every week — the 6-3032 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302 — and every part ships genuine, no aftermarket substitution unless you ask for it.