The Challenger 6-3696 safety decal set is the direct replacement for the Challenger lift it came off of. This is the genuine Challenger part — same fit and same working specification as the one already on your lift. Ordering the Challenger safety decal set from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.

Specifications

• Part number: 6-3696
• Brand: Challenger
• Type: Genuine OEM safety decal set
• Fits: 4018XFX

Support parts fail in quiet ways that are easy to ignore. An airline cracks and the locks won't release cleanly; a decal fades until nobody can read the load rating; a bolt backs out or a thread strips; a lost manual means the next repair is a guessing game. None of these strand the lift the way a blown cylinder does — they just chip away at how safely and correctly it runs until something bigger goes wrong.

What lifts this safety decal set fits

This safety decal set fits the lift models below. Click a model to open its visual parts breakdown — the exploded drawing with every part numbered, so you can confirm this is the right part for your exact lift before you order.

• 4018XFX — see the exploded parts breakdown for this lift

Related parts for this lift

The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.

• Challenger 6-1637 Decal 4-Post Safety Locks
• Challenger 6-1764 12K Capacity Decal
• Challenger 6-3031 Decal Up
• Challenger 6-3032 Decal Down
• Challenger 6-3558 Decal Safety Release
• Challenger 6-3623 Decal Duty Cycle

Replacing your safety decal set

Replacing an airline is quick work — cut the new line to length, seat it fully in its push-connect or threaded fittings, and route it clear of pinch and chafe points. Then pull the lock release and confirm the air actuates every pawl cleanly and together. Since the air side controls the locks, the step-by-step guide is worth a look before you rely on it. Not sure on the procedure? Find your lift in our parts lookup or call and we will walk you through it.

Find the right part for your lift

Not certain this is the exact part your lift needs? Start with your lift's model and serial off the data plate, then open our Challenger parts lookup to see the visual parts breakdown for your model — the exploded drawing with every part numbered and priced. If your plate is missing or unreadable, our guide to finding your model number walks through where to find it, or send us a photo and we will identify the lift for you.

Signs it's time to replace it

For the air supply and regulator, confirm steady, correct pressure. Watch the gauge while the lock release cycles — pressure should hold, not sag. A regulator that drifts, a compressor that can't keep up, or water in the line all keep the pneumatics from working reliably. Drain any moisture trap and check that the delivered pressure matches what the lift's lock system needs to actuate cleanly.

Parts commonly replaced at the same time

Small parts are a good moment to catch up on the rest — decals that are fading, hardware that is due, accessories that pair with what you are buying. We keep the parts breakdown for your model, so one call can round out the order and save you a second wait.

Safety notes

Small parts still matter on a lift. Whether it is a decal an inspector checks for or an accessory that has to be rated for the load, use the correct item for your model and install it the way the manual specifies. Cutting a corner on a small part is still cutting a corner on a lift.

Before you order

A quick prep before ordering: model, serial, and what the part is for. Even minor components come in model-specific versions, and the right one depends on details on your data plate. Call and we will confirm before anything ships.

Ordering the right revision

Before this goes in the cart, grab two things off your lift: the model number and the serial number, both on the manufacturer's plate. The serial matters more than most people expect — lift makers revise components between production runs without renaming the lift, and the run your serial falls in determines which revision of this part is correct.

If you are working from a failed part rather than a plate, measure what you have and photograph how it mounts. Send that to us along with the lift brand, and we will check it against the same parts breakdowns our own techs use in the field before you commit to the order.

Why buy your Challenger safety decal set from Auto Lift Services

We install, inspect, and repair Challenger lifts every week — the 6-3696 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302 — and every part ships genuine, no aftermarket substitution unless you ask for it.