The Rotary FC548-5 replacement hardware is the direct replacement for the Rotary lift it came off of. Cross-referenced as ALS-7516-59, it is the genuine Rotary part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Rotary replacement hardware from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-7516-59
- Brand: Rotary
- Type: Genuine OEM replacement hardware
- Fits: AR120EL1, AR120L, AR120S, FLS25, QL4P100, QL4P101, SM120, SM121EL2, SM121L
- Lift type: 4-post lift
On lift hardware, fit is the whole job. A pin is not a rod of roughly the right diameter — it is a specific length, a specific fit in its bore, and a specific way of being retained, whether that is an e-clip groove, a cotter key hole, or a shoulder. A bushing is a precise interference in its housing and a precise clearance on its shaft. Manufacturer-spec hardware carries all of those dimensions; the hardware-aisle stand-in carries some of them, and the missing ones become play, wobble, and premature wear. This is a spec-correct replacement for the assembly it belongs to — it goes in the way the original came out, retained the way the original was retained.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
- Slotted Bracket - Rotary FC5224-35
- Yoke Weldment-Rear $ 1,191.23 $ 1,072.11 - Rotary - FC5528-1
- Spring Tie-Off - Rotary - FC5529-15
- Pin - Rotary - FC5341-57
- Sleeve Bearing - Rotary - FC5341-73
- Sleeve Bearing - Rotary - FC5341-71
Not sure this fits? Here's how to check
Pull the number off your lift's model plate first — model and serial both. Manufacturers run mid-cycle revisions that keep the model name but change hardware, so two lifts with the same name on the column can take different parts. The serial is what removes the guesswork.
Second check: compare the old part against this listing before you order. Length, mounting pattern, and thread sizes tell most of the story. If anything doesn't line up, or if the old part is too worn or broken to measure, call us with photos — we work on these lifts every week and can usually confirm fit from a picture and the lift's serial faster than you can dig through a parts diagram.
Lay the new piece against the old before installing: length, diameter, groove and hole positions, thread pitch. If the old part is too worn to compare against, check the new part in its bore or against its mate by hand — it should fit the way a machined part fits, snug and smooth, not loose and not forced. Replace the retaining clips and keys while you are there; they are one-use money.
Retention is not optional. A pin without its e-clip, cotter key, or bolt is a pin working its way out under vibration, and what it drops depends on where it lives. If the retainer came off damaged, replace it — never spring a used clip back on and call it held.
Why buy your Rotary replacement hardware from Auto Lift Services
We install, inspect, and repair Rotary lifts every week — the ALS-7516-59 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine Rotary — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this fc548 anti friction
Sourcing the correct fc548 anti friction is not the spot a shop wants to gamble. This piece sits inside a load path the lift manufacturer engineered to specific tolerances, and a substitute that looks close but is off by even a small margin can transfer load onto a neighboring component that was not designed for it. We stock this exact part to the OEM specification the original manufacturer publishes, which is why techs who have been through a bad aftermarket cycle keep coming back to us for the same replacement whenever their next need comes up.
Technical specification & installation notes
Cycle life on this piece depends heavily on operating conditions. In a typical commercial repair shop running 6-10 lifts per day, the fc548 anti friction should deliver five to eight years of service before showing measurable wear against the OEM inspection specification. In a high-volume tire or alignment shop running 20+ lifts per day per bay, expect service every three to five years. It is designed to be a serviceable component; when it does wear it wears within safe operating margins that trigger visible symptoms — drift, uneven wear, minor leakage — well before failure becomes a safety issue.
Shipping & ordering
Freight covers the continental United States on all standard orders. We ship UPS or FedEx ground for parts under 30 lb; heavier assemblies quote at published carrier rates. International orders on the fc548 anti friction require a freight quote — email dimensions, weight, and destination country to [email protected] and we return a rate within one business day. Alaska, Hawaii, and US territories quote at published rates and typically take five to ten business days depending on carrier and destination.
Warranty coverage
Return policy on the fc548 anti friction follows our store-wide standard: all parts sales are final; exchanges only if the piece arrives defective. In the case of a defective delivery, ship the failed piece back to us at your cost, we verify the defect on receipt, and ship a replacement at ours. Wrong-item deliveries where we made the shipping error follow a different path — we reimburse the return shipping cost and cover freight on the correct part. Contact [email protected] with the order number to start either process.
Cross-reference & fitment
Cross-reference on the fc548 anti friction is straightforward: match the OEM part number from the lift's parts breakdown against the number on your original invoice. If the numbers match, the component fits. If your lift's parts breakdown lists a superseded or alternate number, we accept the superseded value on the phone as confirmation of fit. When a manufacturer has issued a running change during production, we track the change in our catalog so ordering by the older number automatically pulls the current-spec replacement.
Questions about the fc548 anti friction? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
Anti-Friction Washer .060 Thick - Rotary FC548-5
Parts that fit your lift
This Rotary part fits the lift models below. Click your model to see every part that fits it — handy for grabbing the wear items that usually go at the same time (cables, sheaves, pins, locks).
Browse all Rotary lift parts →Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.