The Rotary JK238 replacement part is the direct replacement for the Rotary lift it came off of. Cross-referenced as ALS-9762-81, it is the genuine Rotary part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Rotary replacement part from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.
Specifications
- Part number: ALS-9762-81
- Brand: Rotary
- Type: Genuine OEM replacement part
- Fits: BU10A-100, BU10H-100, DRT10A MKII Plunger Parts, DRT10A MKVI Plunger Parts, DRT10A Plunger Parts, DRT10H MKII Plunger Parts, DRT10H MKVI Plunger Parts
- Lift type: inground lift
Do the math on a dead lift bay: a bay that bills steadily is producing hundreds of dollars a day, and the part holding it hostage is very often something small. That is the real cost equation on lift parts — not the price on this page, but the days between failure and repair. The shops that feel it worst are the ones that wait until a part strands a vehicle in the air on a Friday. Keeping the known wear items on hand, or ordering them the day symptoms show up, keeps a twenty-dollar part from charging you a week’s rent on the bay it shut down.
Related parts for this lift
The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.
- DRT10A - Semi-Hydraulic - Rotary JK1154-1
- DRT10H - Full Hydraulic - Rotary JK1155-1
- Right Hand Yoke - Rotary FJ2232
- Seal 10" Wiper - Rotary - JK231
- Seal 10-5/8" High Pressure - Rotary - JK232
- Seal & Gland Spacer Kit 1" Thick - Rotary - JK236
Not sure this fits? Here's how to check
Pull the number off your lift's model plate first — model and serial both. Manufacturers run mid-cycle revisions that keep the model name but change hardware, so two lifts with the same name on the column can take different parts. The serial is what removes the guesswork.
Second check: compare the old part against this listing before you order. Length, mounting pattern, and thread sizes tell most of the story. If anything doesn't line up, or if the old part is too worn or broken to measure, call us with photos — we work on these lifts every week and can usually confirm fit from a picture and the lift's serial faster than you can dig through a parts diagram.
While the lift is already apart, replace what is on the same clock. Parts that wear together should be replaced together — the labor of opening the lift up is the expensive half of the job, and doing it twice for two parts that could have shipped in one box is the most common money leak in lift maintenance. Check the mating parts, the hardware, and anything you had to disturb to get here.
Downtime pressure is exactly when shortcuts happen — the temporary fix, the not-quite-right part, the lock that gets bypassed for one job. Do not let a busy schedule talk you into running a lift in a condition you would flag on someone else’s equipment.
Why buy your Rotary replacement part from Auto Lift Services
We install, inspect, and repair Rotary lifts every week — the ALS-9762-81 is a part we handle in the shop, not a random SKU we drop-ship.
- The phone answers if you have a question mid-install — call 800-674-9302.
- We confirm the right part for your lift's serial and production year before you order.
- Every part ships as genuine Rotary — no aftermarket substitution unless you specifically ask for an aftermarket equivalent.
If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job.
About this jk238 seal wiper
Every order for the jk238 seal wiper starts with a fitment confirmation. Two lifts of the same model can carry subtle revisions between production years, and a component that fits a rev-A lift may not fit a rev-B lift built two years later. Before your card is charged we verify the piece against the parts breakdown for your specific lift serial number. That five-minute step is the difference between the part arriving and being installed the same afternoon versus the wrong piece showing up and the shop losing a day of billable work.
Technical specification & installation notes
Torque and installation notes for this component follow the manufacturer's service manual. Where a torque value is called out, use a calibrated torque wrench and follow the tightening sequence the manual publishes for that fastener location — many lift assemblies require star-pattern or crosswise tightening to distribute load evenly. Skipping that step is one of the most common reasons a correctly-sourced jk238 seal wiper still ends up needing to be re-serviced within a year. Our tech line at 800-674-9302 will walk your installer through the procedure if the shop does not have the current service manual on hand.
Shipping & ordering
Placing an order online is the fastest path — add to cart, check out, done. If the shop needs a purchase order, net-30 terms, or a formal quote for a fleet-service contract, our accounts team handles those via email at [email protected] or by phone at 800-674-9302. Volume pricing on the jk238 seal wiper kicks in at 10+ pieces on the same order for common wear items. Ask about the volume rate specifically before you check out — many fleet buyers stock 6-12 pieces at a time and the discount is meaningful over that shelf life.
Warranty coverage
Every jk238 seal wiper sold through Automotive Lift Services carries a one-year manufacturer-defect warranty. If it fails within that window due to a defect in material or workmanship, we replace it at no charge. Damage from improper installation, use outside the lift's rated capacity, side-loading, or modifications to the parent lift are not covered. The warranty is documented on your original order receipt — retain that record for the coverage period. To submit a warranty claim, contact us with the order number and a photo of the failure at [email protected].
Cross-reference & fitment
Alternate applications for the jk238 seal wiper sometimes exist. Where a common part fits multiple lift models across a manufacturer's catalog, cross-reference sheets show the compatible models explicitly. If you are consolidating parts stock and want to know which of your lifts the piece covers, email the request to [email protected] with a list of the lift models in your bay — we return a compatibility grid showing which lifts accept the replacement and which need a different number.
Questions about the jk238 seal wiper? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
10-5/8" Seal and Wiper (1-piece) - Rotary JK238
Parts that fit your lift
This Rotary part fits the lift models below. Click your model to see every part that fits it — handy for grabbing the wear items that usually go at the same time (cables, sheaves, pins, locks).
Browse all Rotary lift parts →Inspect your lift.
Free. In your browser.
Our free lift inspection walks your lift end to end and shows you exactly which parts you need — right on the exploded diagram. No signup, no charge.