The Challenger A2010-P-02 column component is the direct replacement for the Challenger lift it came off of. This is the genuine Challenger part — same fit and same working specification as the one already on your lift. Ordering the Challenger column component from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same.

Specifications

• Part number: A2010-P-02
• Brand: Challenger
• Type: Genuine OEM column component

Structural parts fit by geometry and rating, and both matter. A pad has to match the arm's cup or bolt pattern; an adapter has to reach the right height and clear the rocker; a carriage and its hardware are specific to the column they ride. A part that's close but not right sits proud, loads a corner, or won't seat flat — and on a component that carries the vehicle, "close enough" isn't a spec worth trusting.

Related parts for this lift

The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit.

• Challenger A2010-I Idler Column Weldment-Cl10
• Challenger A2010-I-04 Idler Column Weldment-Cl10
• Challenger A2010-I-06 Idler Column Weldment-Cl10
• Challenger A2010-I-10 Idler Column Weldment Cl10 Green
• Challenger A2010-I-67 Idler Column Weldment-Cl10
• Challenger A2010-P Power Column Weldment-Cl10

Replacing your column component

Swapping arm pads is one of the simplest jobs on a lift — pop the old pad, seat the new one in the arm's cup or bolt pattern — but it's also one of the most important, because the pad is what grips the car. Confirm the new pads match the arms and sit flush. Even so, the full procedure is worth a quick read before you put a vehicle back on them. Not sure on the procedure? Find your lift in our parts lookup or call and we will walk you through it.

Find the right part for your lift

Not certain this is the exact part your lift needs? Start with your lift's model and serial off the data plate, then open our Challenger parts lookup to see the visual parts breakdown for your model — the exploded drawing with every part numbered and priced. If your plate is missing or unreadable, our guide to finding your model number walks through where to find it, or send us a photo and we will identify the lift for you.

Signs this part is worn out

For ramps and approach parts, look for bends, cracks, and worn hinge points. A ramp that's bent won't sit flush and can kick out when a car drives up; a cracked hinge or worn pivot lets it shift. Check that stops and retainers are present and that the ramp locks where it should. A ramp is load-bearing at the moment of drive-on, so bends and cracks there matter.

Parts commonly replaced at the same time

While you are replacing this, check its companions: worn pads often ride with worn adapters and elongated pin bores. Replacing the set keeps the vehicle sitting square on the lift. Tell us your model and we will build the pad-and-adapter kit plus the mounting hardware so nothing is left worn.

Safety notes

The parts that touch the vehicle — pads, adapters, ramps, arm hardware — are what keep it from slipping off the lift. Once a pad is crushed, a lip is bent, or a pin hole has wallowed out, the safe grip is gone. Swap them at the first sign of wear rather than trusting a vehicle to a worn contact point.

Before you order

Get the structural order right by matching the old part: shape, size, and mounting style all vary by model. Most contact parts belong in sets, so replace them together for even support. Confirm model and serial when you call and we will make sure the fit is correct before it ships.

Check your lift's serial before ordering

The most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so "it fits my lift model" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift.

Can't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week.

Why buy your Challenger column component from Auto Lift Services

We install, inspect, and repair Challenger lifts every week — the A2010-P-02 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302 — and every part ships genuine, no aftermarket substitution unless you ask for it.